Avaya Connecting BayStack AN and ANH Platforms to a Network Manuale Utente Pagina 37
- Pagina / 178
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Hardware and Software Overview
114074 Rev. A 1-11
Obtaining the IP Address Manually (Netboot and Directed Netboot)
For Netboot and Directed Netboot, you configure the IP address manually.
Chapter 4 describes how to use Site Manager to configure Netboot interfaces.
Chapter 5 describes how to configure the netboot interfaces using the Technician
Interface.
Obtaining the IP Address Automatically (EZ-Install)
During the EZ-Install process, the router obtains its address automatically, as
described below.
1. When you power on the AN/ANH, it runs a set of diagnostic tests.
2. The AN/ANH sends a BOOTP request to the upstream router for an IP
address and subnet mask.
The AN/ANH issues the request through all synchronous ports at about the
same time, even if cables are not connected to these ports. Each port
successively tries the following protocols until it receives a response:
• Bay Networks Standard PPP using HDLC (high-level datalink control)
encapsulation
• Frame Relay Annex D
• Frame Relay Local Management Interface (LMI)
• Frame Relay Annex A
The AN/ANH makes two attempts for each protocol. If it does not receive a
response in approximately 4 minutes, the AN/ANH boots the default image
and configuration file in its local file system, as described in the next section,
“
Local Boot.”
3. The first interface on the upstream router to receive the BOOTP request
responds.
4. The upstream router calculates the IP address of the AN/ANH’s
synchronous interface.
How the upstream router calculates the IP address depends on its protocol
configuration. See Step a if the upstream router circuit is running Bay
Networks Standard or is a Frame Relay permanent virtual circuit (PVC) in
direct access mode. See Step b if it is a Frame Relay PVC in group access
mode.
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- 114074 Rev. A vii 7
- 114074 Rev. A ix 9
- 114074 Rev. A 10
- 114074 Rev. A xi 11
- 114074 Rev. A xiii 13
- About This Guide 15
- Before You Begin 16
- Conventions 17
- Acronyms 18
- 114074 Rev. A xix 19
- 114074 Rev. A xxi 21
- Bay Networks Customer Service 22
- World Wide Web 23
- Customer Service FTP 23
- Support Source CD 24
- CompuServe 24
- InfoFACTS 25
- How to Get Help 25
- Chapter 1 27
- 1-2 114074 Rev. A 28
- ANH Models 29
- 1-4 114074 Rev. A 30
- Access Node Software 31
- Software Management Tools 32
- Router Software 32
- Boot Configuration Options 33
- 1-8 114074 Rev. A 34
- The Boot Process 36
- 114074 Rev. A 1-11 37
- CAN0001A 38
- 114074 Rev. A 1-13 39
- 114074 Rev. A 1-15 41
- Local Boot 42
- CAN0006A 43
- Chapter 2 45
- EZ-Install 46
- Booting the Router Routinely 47
- Directed Netboot 48
- Completing a Startup Option 49
- 114074 Rev. A 2-7 51
- 2-10 114074 Rev. A 54
- Chapter 3 55
- Setting Up a UNIX Boot Server 55
- Setting Up BOOTP Sockets 56
- Setting Up BOOTPD to Run 57
- 3-6 114074 Rev. A 60
- 3-8 114074 Rev. A 62
- Setting Up a TFTP Server 63
- The examples in 64
- 114074 Rev. A 3-11 65
- 3-12 114074 Rev. A 66
- What to Do Next 67
- Chapter 4 69
- Configuring Network Booting 69
- Creating Configuration Files 70
- Preparing an Image 71
- Configuring Network Booting 75
- 4-8 114074 Rev. A 76
- 2. Click on Add 76
- Click on OK 77
- (Figure 4-4) 77
- 79
- 80
- CAN0007A 82
- 114074 Rev. A 4-15 83
- 4-16 114074 Rev. A 84
- 114074 Rev. A 4-17 85
- 4-18 114074 Rev. A 86
- 1. Click on Client I/F 87
- Chapter 5 91
- Network Boot Client 91
- <TFTP host> 92
- (continued) 92
- <TFTP 93
- (continued) 93
- <interface> 94
- <next 94
- <interface> 95
- <IP address> 95
- <subnet mask> 95
- <next hop 95
- 114074 Rev. A 5-8 98
- Chapter 6 99
- 101
- 6-4 114074 Rev. A 102
- 114074 Rev. A 6-5 103
- 6-6 114074 Rev. A 104
- About the N11 DCM 105
- 6-8 114074 Rev. A 106
- Ethernet Statistics Group 107
- Host Group 107
- HostTopN Group 108
- Matrix Group 108
- Filter Group 108
- Packet Capture Group 108
- Enabling the DCM 109
- 111
- 112
- 112
- 113
- 113
- 114
- 114074 Rev. A 6-19 117
- 2. Click on OK 119
- RMON Implementation Notes 121
- RMON Interoperability Issues 121
- 6-24 114074 Rev. A 122
- 114074 Rev. A 6-25 123
- 6-26 114074 Rev. A 124
- 114074 Rev. A 6-27 125
- 6-28 114074 Rev. A 126
- 114074 Rev. A 6-29 127
- Appendix A 129
- Router Fails to Netboot 131
- 114074 Rev. A A-5 133
- <connector> 135
- 114074 Rev. A A-9 137
- Displaying Parameter Settings 138
- 114074 Rev. A A-11 139
- Debugging the BOOTP Server 140
- Table A-1. BOOTP Messages 141
- <IP_address> 143
- Upgrading the Software Image 145
- Restoring a Local File System 145
- Appendix B 147
- Global Information Worksheet 149
- Router Protocol Worksheets 151
- OSPF Worksheet 152
- Wide-Area Protocol Worksheets 154
- Frame Relay Worksheet 155
- PPP Standard Worksheet 156
- CAN0008A 160
- Appendix C 161
- Implementation Notes 161
- C-2 114074 Rev. A 162
- Network Configuration Options 163
- Configuring a Single ANH 164
- 114074 Rev. A C-5 165
- Configuring Multiple Hubs 166
- CAN0010A 167
- C-8 114074 Rev. A 168
- CAN0011A 169
- CAN0012A 170
- 114074 Rev. A Index-1 171
- 114074 Rev. A Index-3 173
- 114074 Rev. A Index-5 175
- 114074 Rev. A Index-7 177
Prodotti e manuali riguardandi Software Avaya Connecting BayStack AN and ANH Platforms to a Network
Software Avaya Nortel Business Communications Manager 450 1.0 Administration and Security Manuale Utente
(200 pagine)
(200 pagine)
Software Avaya BCM 4.0 Manuale Utente
(398 pagine)
(398 pagine)
Software Avaya Business Communications Manager - Multimedia Contact Center Manuale Utente
(38 pagine)
(38 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale