Avaya Using Technician Interface Scripts Manuale Utente

Using Technician InterfaceScripts Router Software Version 10.0Site Manager Software Version 4.0Software Version BNX 6.0Site Manager Software Version

x Appendix A Packet Configuration config packet line [<line_number>] ...

Using Technician Interface Scripts2-48Sample Display – show at configurationAppleTalk Base Configuration---------------------------- Mode NBP Reg

show at2-49disabledDisplays all disabled circuits that contain an AppleTalk port. A circuit is disabled if the disable/enable parameter is set to disa

Using Technician Interface Scripts2-50filters zone [circuit <circuit name>]Displays information about the zone filters for all circuits or a speci

show at2-51Total zones for circuit E21 is 2 Circuit: E32 AppleTalk Port: #3 Port Filter Mode: 5.x series Include Filtered Zone(s) for

Using Technician Interface Scripts2-52Sample Display – show at routesAppleTalk Routing Table----------------------- Network Hop Next Hop St

show at2-53Sample Display – show at routes zones Network Hop Next Hop State Port Zone List ----------- --- ---------------

Using Technician Interface Scripts2-54The table includes the following information:Sample Display – show at stats ddpAppleTalk DDP Statistics---------

show at2-55total [routes | nets | zones | aarp]Displays totals for all dynamic protocol-specific information or for the specified parameter.Sample Displ

Using Technician Interface Scripts2-56The table includes the following information:Sample Display – show at zonesAppleTalk Zone Table-----------------

show at2-57Sample Display – show at zones find net*AppleTalk Zone Table-------------------- Network Zone Name -----------

xi Tables Table 1-1. Displaying Service Information ...1-8Table 1-2. Enabling and Disab

Using Technician Interface Scripts2-58show atmThe show atm <option> commands display information about the Asynchronous Transfer Mode (ATM) Adap

show atm2-59alertsDisplays abnormal conditions in the ATM interface. Use this command to identify lines configured as enabled but not currently up. The

Using Technician Interface Scripts2-60enabledDisplays the ATM interfaces that are configured as enabled. For more information about column definitions,

show atm2-61Sample Display – show atm interfacesATM Interface Table------------------- Line Circuit State VPCs VCCs Address Type ----

Using Technician Interface Scripts2-62Sample Display — show atm vcsATM Interface VCL Table----------------------- Hybri

show atm2-63services [<line>] | [<line.circuit>]Displays all ATM service record instances, or a subset of service record instances, along

Using Technician Interface Scripts2-64statsDisplays statistical information about all ATM PVCs. The table includes the following information:Sample Di

show atm2-65stats pvc [<line>] | [<line.VPI>] | [<line.VPI.VCI>]Displays all ATM PVC statistics or a subset of ATM PVC statistics.Fo

Using Technician Interface Scripts2-66show atmarpThe show atmarp <options> command displays ATMARP information. For details about the Bay Networ

show atmarp2-67interface [<IP_address>]Displays interface information for all ATMARP interfaces, or a specific interface.The table displays the f

Using Technician Interface Scripts2-68Sample Display – show atmarp stats Open Calls Calls Failed Failed Calls In

show atmarp2-69Sample Display – show atmarp tableIP address Life ATM address Vpi.vci--------------- ----- ---

Using Technician Interface Scripts2-70show atmdxi The show atmdxi <option> commands display information about Asynchronous Transfer Mode Data Ex

show atmdxi2-71alertsDisplays abnormal conditions in the ATM DXI line level. Use this command to identify lines configured as enabled but not currently

Using Technician Interface Scripts2-72Sample Display – show atmdxi baseATM Data Exchange Interface (DXI) Base Record----------------------------------

show atmdxi2-73lines [<line.llindex>]Displays all ATM DXI interfaces or a just a specific line. The table includes the following information:Samp

Using Technician Interface Scripts2-74pvcs [<line.llindex>] | [<line.llindex.VPI>] | [<line.llindex.VPI.VCI>]Displays all or a s

show atmdxi2-75Sample Display – show atmdxi pvcs ATM Data Exchange Interface (DXI) PVC Table-------------------------------------------Line.LLIndex.VP

Using Technician Interface Scripts2-76stats lmiDisplays statistics for all active ATM DXI Local Management Interfaces (LMIs). The table includes follo

show atmdxi2-77stats mpeDisplays statistics for all active ATM DXI multiprotocol encapsulated interfaces. The information is from the circuit level ra

xiii About This Guide Use this guide if you are responsible for monitoring and maintaining the performance of Bay Networks routers and BNX platfor

Using Technician Interface Scripts2-78stats pvc [<line.llindex>] | [<line.llindex.VPI>] | [<line.llindex.VPI.VCI>]Displays ATM D

show atmsig2-79show atmsig The show atmsig <options> command displays information about the ATM Signaling service. For details about the Bay Net

Using Technician Interface Scripts2-80Sample Display – show atmsig ilmiATM ILMI Entry Table (UME/ILMI)-------------------------------

show atmsig2-81Sample Display – show atmsig saalATM SAAL Entry Table (SSCOP)---------------------------- Arbi- Poll Alive NoR

Using Technician Interface Scripts2-82State State of the entity: Up, Down, Initializing, Not PresentMax # of SvcApps Maximum number of service access

show atmsig2-83Sample Display – show atmsig sigATM Signaling Entry Table (Q.93B)--------------------------------- Max#of Max

Using Technician Interface Scripts2-84show atm lineThe show atm line <option> commands display information about the Asynchronous Transfer Mode

show atm line2-85alertsDisplays abnormal conditions in the ATM link module. The table displays the following information:Sample Display – show atm lin

Using Technician Interface Scripts2-86base [circuit <circuit name>]Displays the ATM base record state for all ATM link module circuits or for a

show atm line2-87disabledDisplays the ATM link modules that are configured as disabled. For more information on column definitions, see the alerts comma

Using Technician Interface Scriptsxiv Software Suites Routing and Switching software is available in the following suites.• The System Suite includ

Using Technician Interface Scripts2-88phy [circuit <circuit name>]Displays physical circuit information about all ATM link module circuits or a

show atm line2-89phy errors [circuit <circuit name>]Displays loss of signal, loss of pointer, loss of frame, and out-of-cell delineation informa

Using Technician Interface Scripts2-90receive errors [circuit <circuit name>]Displays receive error information for the specified circuit or for

show atm line2-91Sample Display – show atm line receive errors circuit A51ATM Module Receive Errors:--------------------------

Using Technician Interface Scripts2-92sample [<period in seconds>] [circuit <circuit name>]Displays the total number of frames transmitted

show atm line2-93Sample Display – show atm line sample 5 circuit A51ATM Sampled Data over 5 seconds---------------------------------

Using Technician Interface Scripts2-94transmit errors [circuit <circuit name>]Displays the total number of full errors transmitted and the total

show atm line2-95transmit stats [circuit <circuit name>]Displays the total number of frames, octets, and cells transmitted by the specified circu

Using Technician Interface Scripts2-96show aurpThe show aurp <option> commands display information about the AppleTalk Update-based Routing Prot

show aurp2-97Sample Display – show aurp alertsAURP Connection Alerts: Enabled but state is down------------------------------------------------- Con

About This Guidexv Before You Begin Before using this guide to run Technician Interface commands on a router or BNX platform, you must• Install the r

Using Technician Interface Scripts2-98Sample Display – show aurp baseAURP Base Information--------------------- Configu

show aurp2-99Sample Display – show aurp connection 192.32.14.85AURP Connections---------------- Connection State Timeout Retry Upda

Using Technician Interface Scripts2-100Sample Display – show aurp enabledEnabled AURP Connections------------------------ Connection State

show aurp2-101Sample Display – show aurp filters zone Connection: 192.32.14.2 Connection Filter Mode: Include Filtered Zone(s) for thi

Using Technician Interface Scripts2-102stats [traffic | peer | transport] [<IP address>]Displays statistical information about AURP connections.

show aurp2-103Sample Display – show aurp stats traffic 205.1.10.1AURP Traffic Statistics----------------------- In DDP Out DDP

Using Technician Interface Scripts2-104Sample Display – show aurp stats peerAURP Connection Peer Information--------------------------------

show aurp2-105versionDisplays the current version and modification date of the aurp.bat script.Sample Display – show aurp versionAURP.bat Version: 1.5

Using Technician Interface Scripts2-106show autonegThe show autoneg <option> commands display the status of automatic line speed negotiation on

show autoneg2-107Sample Display – show autoneg alertsAuto-Negotiation Interfaces on Alert:-------------------------------------

Using Technician Interface Scriptsxvi Customers also have the option of purchasing direct support from Bay Networks through a variety of service prog

Using Technician Interface Scripts2-108capabilities [circuit <circuit name>]Displays Ethernet line capabilities. You can display this informatio

show autoneg2-109disabledDisplays all Ethernet circuits that have auto-negotiation disabled. Sample Display – show autoneg disabledAuto-Negotiation In

Using Technician Interface Scripts2-110Sample Display – show autoneg enabledAuto-Negotiation Interfaces Enabled:------------------------------------

show bgp2-111show bgp The show bgp <option> commands display state, configuration, and statistical information about the Border Gateway Protocol

Using Technician Interface Scripts2-112errorsDisplays the error message generated the last time a connection between a router and its BGP peer failed.

show bgp2-113Sample Display – show bgp peersBGP Peers--------- Local Remote Remote Peer Connection BGP Total Addr

Using Technician Interface Scripts2-114routes [<address> | from <peer address> | find <search pattern>]Displays information about

show bgp2-115The show bgp routes command displays the routing information in the following format:Aggregator If it exists, the aggregator attribute; d

Using Technician Interface Scripts2-116Sample Display – show bgp routesBGP Routes----------0.0.0.0/0 from 192.32.28.104 (BEST, USED) nexthop 192.32.28

show bgp2-117 statsDisplays statistics for each peer router. The table displays the Internet address of the configured local and remote BGP peers and t

About This Guidexvii InfoFACTS InfoFACTS is the Bay Networks free 24-hour fax-on-demand service. This automated system contains libraries of technica

Using Technician Interface Scripts2-118Sample Display – show bgp summaryBGP Up ID: 192.32.174.98 AS: 2 IBGP Hack Disabled2 peers configured.U

show bgp2-119Sample Display – show bgp timersBGP Peer Timers------------------- Local Remote Keep Time Las

Using Technician Interface Scripts2-120show bisyncThe show bisync <option> commands display configuration, status, and statistical information ab

show bisync2-121alertsDisplays all BISYNC circuits that are enabled but not up. Use this display to identify the interfaces that are not working. The

Using Technician Interface Scripts2-122Sample Display – show bisync alertsBISYNC Modules on Alert:---------------------- Li

show bisync2-123disabledDisplays BISYNC circuits that a user has manually disabled. Sample Display – show bisync disabledBISYNC Modules Disabled:-----

Using Technician Interface Scripts2-124interrupt errors [circuit <circuit name>]Displays interrupt errors in character reception. The BISYNC dri

show bisync2-125receive errors [circuit <circuit name>]Displays receive errors for all circuits or for a specific circuit. The table includes the

Using Technician Interface Scripts2-126sample [<period in seconds>] [circuit <circuit name>]Displays data sampled from BISYNC over a perio

show bisync2-127stats [circuit <circuit name>]Displays BISYNC input/output statistical information for all BISYNC modules or for a specific circu

Using Technician Interface Scriptsxviii Conventions This section describes the conventions used in this guide.angle brackets (< >) Indicate tha

Using Technician Interface Scripts2-128transmit errors [circuit <circuit name>]Displays statistical information about transmission errors for al

show bisync2-129versionDisplays the current version and modification date for the bisync.bat script.Sample Display – show bisync versionbisync.bat Vers

Using Technician Interface Scripts2-130show bootpThe show bootp <option> commands display configuration, state, and statistical information about

show bootp2-131Sample Display – show bootp baseBootp Base Information---------------------- Interface Min Max Address

Using Technician Interface Scripts2-132prefservDisplays information about each entry in the preferred servers table. The table includes the following

show bootp2-133Sample Display – show bootp ragentsBootp Relay Agents------------------ Agent Address Outbound Address State PassThruMode -------

Using Technician Interface Scripts2-134Sample Display – show bootp statsBootp Statistics---------------- Interface Dropped Requests Replie

show bot2-135show botThe show bot <option> commands display information about the Binary Synchronous Communication (BSC) transport services. For

Using Technician Interface Scripts2-136alertsDisplays all BTS circuits that are enabled but not up. Use this command to identify interfaces that are n

show bot2-137 baseDisplays the base record information for BTS. The base record controls BTS for the entire system. Sample Display – show bot baseBOT

About This Guidexix Ordering Bay Networks Publications To purchase additional copies of this document or other Bay Networks publications, order by pa

Using Technician Interface Scripts2-138CUsDisplays all BTS connections from this router to control units. The table includes the following information

show bot2-139disabledDisplays all disabled circuits that contain an BTS port. A circuit is disabled if you set the Enable parameter to disable and the

Using Technician Interface Scripts2-140peersDisplays all BTS peer connections for this router.Sample Display – show bot peers BOT Peer Table ---------

show bot2-141Sample Display – show bot stats BOT Circuit Statistics ---------------------- Circuit Interface Interfac

Using Technician Interface Scripts2-142show bridgeThe show bridge <option> commands display configuration, state, and statistical information abo

show bridge2-143Sample Display – show bridge alertsBridge Circuit Table-------------------- Frame 802.9 Circuit

Using Technician Interface Scripts2-144circuits [<circuit name>]Displays Bridge circuit parameters for all circuits or for a specific circuit. St

show bridge2-145enabledDisplays circuits that are currently enabled. State is Down, Init (initializing), Not Present (enabled but not yet started) or

Using Technician Interface Scripts2-146Sample Display – show bridge forwarding tablesBridge Forwarding Tables------------------------ MAC Address

show bridge2-147versionDisplays the current version and modification date of the bridge.bat script. Sample Display – show bridge version BRIDGE.bat Ver

4401 Great America Parkway 8 Federal StreetSanta Clara, CA 95054 Billerica, MA 01821 Copyright © 1988–1996 Bay Networks, Inc. All rights reserved. Pr

Using Technician Interface Scriptsxx DOS Disk Operating SystemDRAM Dynamic RAMDSAP Destination Service Access PointEOF End of FileFAT File Allocation

Using Technician Interface Scripts2-148show circuitsThe show circuits <option> commands display specific configuration, state, and statistical inf

show circuits2-149alertsDisplays all enabled circuits whose state is not Up.Sample Display – show circuits alertsCSMACD Modules on Alert:-------------

Using Technician Interface Scripts2-150base [<circuit name>]Displays the circuit base record information for all circuits or for a specific circu

show circuits2-151configuration [<circuit name>]Displays the circuits used on the router. The table includes the circuit type, circuit number, in

Using Technician Interface Scripts2-152Sample Display – show circuits disabledCSMACD Modules Disabled:------------------------

show circuits2-153enabledDisplays all currently enabled circuits.Sample Display – show circuits enabledCSMACD Modules Enabled:-----------------------

Using Technician Interface Scripts2-154hwfiltersDisplays all hardware filter configurations on the router.Sample Display – show circuits hwfiltersHardware

show circuits2-155receive errors [<circuit name>]Displays the receive error statistics for all circuits or for a specific circuit.Sample Display

Using Technician Interface Scripts2-156stats [<circuit name>]Displays the Input/Output statistics for all circuits or for a specific circuit.Samp

show circuits2-157system errors [<circuit name>]Displays the system error statistics for all circuits or for a specific circuit.Sample Display –

About This Guidexxi OSI Open Systems InterconnectionPCMCIA Personal Computer Memory Card International AssociationPPP Point-to-Point ProtocolPPX Para

Using Technician Interface Scripts2-158transmit errors [<circuit name>]Displays the transmit error statistics for all circuits or for a specific

show circuits2-159versionDisplays the current version number and modification date of the circuits.bat script.Sample Display – show circuits versionCIR

Using Technician Interface Scripts2-160show consoleThe show console <option> commands display console port configuration, state, and statistics i

show console2-161Sample Display – show console alertsConsole Serial Port Alert Information------------------------------------- Port Port Po

Using Technician Interface Scripts2-162Port Name Name that the system has given to the port. Users may not specify a name. You can use the name to cor

show console2-163Login Time Out Number of minutes allowed between when the system displays the login banner and a user enters a login ID; relevant onl

Using Technician Interface Scripts2-164Sample Display – show console configurationConsole Serial Port Configuration Information------------------------

show console2-165enabledDisplays the port number, port name, and state of all enabled serial ports. Also displays the number of enabled serial ports a

Using Technician Interface Scripts2-166Sample Display – show console statsConsole Serial Port Statistical Information---------------------------------

show csmacd2-167show csmacdThe show csmacd <option> commands display configuration, status, and statistical information about the Carrier Sense M

Using Technician Interface Scripts2-168Sample Display – show csmacd alertsCSMACD Modules on Alert:------------------------

show csmacd2-169autoneg [circuit <circuit name>]Displays the line speed characteristics of Ethernet circuits that are configured with automatic l

Using Technician Interface Scripts2-170Sample Display – show csmacd autonegAuto-Negotiation Information:-----------------------------

show csmacd2-171collisions [circuit <circuit name>]Displays status on bus collisions. You can display collision information for a specific circui

Using Technician Interface Scripts2-172Sample Display – show csmacd collisionsCSMACD Module Collision Information:------------------------------------

show csmacd2-173Sample Display – show csmacd enabledCSMACD Modules Enabled:----------------------- BOFL

Using Technician Interface Scripts2-174Sample Display – show csmacd hwfiltersHardware Filters Modules:-------------------------

show csmacd2-175Sample Display – show csmacd receiveCSMACD Module Receive Errors:-----------------------------

Using Technician Interface Scripts2-176Sample Display – show csmacd sampleCSMACD Sampled Data over 10 seconds------------------------------------

show csmacd2-177Sample Display – show csmacd statsCSMACD Module I/O Statistics:----------------------------- Receive Receive Tr

1-1 Chapter 1Using Technician Interface Scripts This chapter provides an overview of the Technician Interface scripts and explains how to run them f

Using Technician Interface Scripts2-178Sample Display – show csmacd systemCSMACD Module System Errors:----------------------------

show csmacd2-179Sample Display – show csmacd transmitCSMACD Module Transmit Errors:------------------------------

Using Technician Interface Scripts2-180show dcmmwThe show dcmmw <option> commands display information about an installed N11 Data Collection Mod

show dcmmw2-181baseDisplays the base record information for the DCM software subsystem. The table includes the following information:Application DCMMW

Using Technician Interface Scripts2-182Sample Display – show dcmmw baseDCMMW Base Information--------------------- Application State -----------

show decnet2-183show decnetThe show decnet <option> commands display configuration, state, and statistical information about DECnet Phase IV serv

Using Technician Interface Scripts2-184adjacencyDisplays attributes of the adjacency table. An adjacency is a directly connected circuit-neighbor pair

show decnet2-185alertsDisplays all circuits configured as enabled but not currently up. Use this command to display information about the physical circ

Using Technician Interface Scripts2-186Sample Display – show decnet area routesDECnet Area (Level II Routing) Information-----------------------------

show decnet2-187Sample Display – show decnet baseDECnet Base Record Information------------------------------ Protocol State --------

Using Technician Interface Scripts1-2 What Are Technician Interface Scripts? The Technician Interface scripts are programs that let you manage the ro

Using Technician Interface Scripts2-188Sample Display – show decnet circuitDECnet Circuit Information----------------------------Circuit State Ar

show decnet2-189Sample Display – show decnet designated routerDECnet Designated Router Information------------------------------------ Designa

Using Technician Interface Scripts2-190enabledDisplays all the circuits whose state is enabled. State is Down, INIT (initializing), Not Present (not y

show decnet2-191Sample Display – show decnet node routesDECnet Node (Level I Routing) Information----------------------------------------- Area Node I

Using Technician Interface Scripts2-192Sample Display – show decnet static adjacencyDECnet Static Adjacency Information-------------------------------

show decnet2-193Sample Display – show decnet statsDECnet Statistics----------------- Hello Hello Hello H

Using Technician Interface Scripts2-194Sample Display – show decnet stats updateDECnet Routing Update Statistics--------------------------------

show decnet2-195Sample Display – show decnet stats errorDECnet Error Statistics----------------------- Aged Node Node Oversiz

Using Technician Interface Scripts2-196Sample Display – show decnet traffic filters e41DECnet Traffic Filter Information--------------------------------

show dls2-197show dlsThe show dls <option> commands display configuration, state, and statistical information about Data Link Switching (DLSw) se

Using Technician Interface Scripts1-3 Commands for Scripts Scripts support the following command categories: show Displays configuration, state, and s

Using Technician Interface Scripts2-198alertsDisplays all enabled DLSw circuits whose state is not up. The table does not show configured DLSw circuits

show dls2-199TCP Window Maximum amount of DLSw data that local or remote TCP entities can send before requiring an acknowledgment or receive before ac

Using Technician Interface Scripts2-200Sample Display – show dls baseDLS Base Information-------------------- State TCP Window Uncfg Peer Int R

show dls2-201configurationDisplays the configuration information for the DLSw base record, circuits, slots, peers, SAPs, MACs, NetBIOS names, filters, an

Using Technician Interface Scripts2-202disabledDisplays all DLSw circuits that the user has manually disabled. In this case, State is Disabled. For in

show dls2-203filtersDisplays the currently configured DLSw traffic filters. Sample Display – show dls filtersDLSw Traffic Filters-------------------- Filt

Using Technician Interface Scripts2-204Sample Display – show dls localDLSw Local SDLC Devices----------------------- Destina

show dls2-205Sample Display – show dls macDLSw MAC Entries---------------- Destination Remote CANUREACH MAC Address

Using Technician Interface Scripts2-206peersDisplays the IP addresses of all configured DLSw peers and the state of each. State is Down, Init (initiali

show dls2-207slotsDisplays the slot number, IP address, and memory information that corresponds on the slot to DLSw.Sample Display – show dls slotsDLS

Using Technician Interface Scripts1-4 Each show command supports a subset of commands that display statistical and configuration information about a

Using Technician Interface Scripts2-208show ds1e1The show ds1e1 <option> commands display configuration, status, and statistical information abou

show ds1e12-209alertsDisplays all DS1E1 logical lines that are enabled but not up. Use this display to identify the logical lines that are not working

Using Technician Interface Scripts2-210Sample Display – show ds1e1 alertsDS1E1 Logical Lines on Alert:----------------------------- Log Line

show ds1e12-211Sample Display – show ds1e1 baseDS1E1 Logical Lines:-------------------- Log Line Line WAN Ra

Using Technician Interface Scripts2-212Sample Display – show ds1e1 clockDS1E1 Clock Status:------------------- Current Primary Secondary

show ds1e12-213e1framer [current] [total] [interval [<interval number>] ]Displays error information about the E1 framer. Sample Display – show d

Using Technician Interface Scripts2-214Sample Display – show ds1e1 e1framer intervalE1 Interval Framer Statistics-----------------------------Bipolar

show ds1e12-215e1portDisplays E1 port information.Sample Display – show ds1e1 e1portE1 Port Status:--------------- BERT Line

Using Technician Interface Scripts2-216fdl [ansi1 | ansi2 | att1 | att2 ]Displays the Facility Data Link (FDL) error statistics in both ANSI-403 and A

show ds1e12-217DS1E1 Facility Data Link (FDL) Errors (second half) — ANSI-403 mode:DS1E1 Facility Data Link (FDL) Errors (first half) — AT&T-54016

Using Technician Interface Scripts1-5Loading .bat and .mnu Scripts You can use the Bay Networks implementation of File Transfer Protocol (FTP) to load

Using Technician Interface Scripts2-218DS1E1 Facility Data Link (FDL) Errors (second half) — AT&T-54016 mode:Slot Slot identifier. Conn Connector i

show ds1e12-219Sample Display – show ds1e1 fdlDS1E1 Facility Data Link (FDL) Errors (first half) - ANSI-403 mode:-------------------------------------

Using Technician Interface Scripts2-220Sample Display – show ds1e1 fdl att1DS1E1 Facility Data Link (FDL) Errors (first half) - AT&T-54016 mode:--

show ds1e12-221Sample Display – show ds1e1 receiveDS1E1 Logical Line Receive Errors:---------------------------------- Log Nu

Using Technician Interface Scripts2-222Sample Display – show ds1e1 sampleTaking first sample... Waiting 10 seconds...

show ds1e12-223stats [circuit <circuit name>]Displays DS1E1 input/output statistical information for all DS1E1 circuits or for a specific circuit

Using Technician Interface Scripts2-224Sample Display – show ds1e1 stats circuit BostonDS1E1 Logical Line I/O Statistics:-----------------------------

show ds1e12-225Sample Display – show ds1e1 system errorsDS1E1 Logical Line System Errors:--------------------------------- Log Un

Using Technician Interface Scripts2-226t1framer [current] [total] [interval [<interval number>] ]Displays T1 framer error information.Sample Dis

show ds1e12-227Sample Display – show ds1e1 t1framer intervalT1 Interval Framer Statistics----------------------------- Bipolar Out of

Using Technician Interface Scripts1-6To use the Trivial File Transfer Protocol (TFTP) to transfer files one at a time, refer to Chapters 4 and 5 of Usi

Using Technician Interface Scripts2-228t1portDisplays T1 port information.Sample Display – show ds1e1 t1portT1 Port Status:---------------

show ds1e12-229Sample Display – show ds1e1 timeslotsDS1E1 Timeslot Assignment:-------------------------- |----------Timeslot

Using Technician Interface Scripts2-230Sample Display – show ds1e1 transmit errorsDS1E1 Logical Line Transmit Errors:---------------------------------

show ds1e12-231versionDisplays the current version and modification date for the ds1e1.bat script.Sample Display – show ds1e1 version ds1e1.bat Version

Using Technician Interface Scripts2-232show dvmrpThe show dvmrp <option> commands display configuration, state, and statistical information about

show dvmrp2-233Sample Display – show dvmrp baseDVMRP Base Information---------------------- Protocol State -------- ----------- DVMRP Up

Using Technician Interface Scripts2-234circuits [<circuit name> | enabled | disabled]Displays the DVMRP circuit information for all circuits, a

show dvmrp2-235neighbors [<circuit name>]Displays all DVMRP neighbor information or neighbor information for a specified circuit. The table displ

Using Technician Interface Scripts2-236Sample Display – show dvmrp routes mainDVMRP Main Routes-----------------State: L = Local interface T = Timed

show dvmrp2-237Sample Display – show dvmrp routes vifsDVMRP Virtual Interface Routes------------------------------ State: C = Child L = Leaf

Using Technician Interface Scripts1-7NVFS File System:VOL STATE TOTAL SIZE FREE SPACE CONTIG FREE SPACE---------------------------------

Using Technician Interface Scripts2-238stats circuits [<circuit name>]Displays statistics for all DVMRP circuits or a specified DVMRP circuit. Th

show dvmrp2-239Sample Display – show dvmrp stats tunnelsDVMRP Tunnel Statistics----------------------- Circuit Remote IP Packets Packets Upda

Using Technician Interface Scripts2-240Sample Display – show dvmrp stats vifsDVMRP Virtual Interface Route Statistics---------------------------------

show dvmrp2-241Sample Display – show dvmrp tunnelsDVMRP Tunnels------------- Circuit Local IP Remote IP State Encaps Metric Thre

Using Technician Interface Scripts2-242show e1The show e1 <option> commands display configuration, status, and statistical information about the

show e12-243Sample Display – e1 alertsE1 Modules on Alert:-------------------- HDB3 Clock Slot

Using Technician Interface Scripts2-244base [circuit <circuit name>]Displays the base level information for all E1 circuits or a specific circuit

show e12-245disabledDisplays E1 circuits that a user has manually disabled. For definitions of the columns in the table, see the alerts command.Sample

Using Technician Interface Scripts2-246frame errors [circuit <circuit name>]Displays E1 frame errors for all circuits or for a specific circuit.

show e12-247line errors [circuit <circuit name>]Displays several categories of line errors for all circuits or for a specific circuit. The table

Bay Networks, Inc. 4401 Great America Parkway, Santa Clara, CA 950548 Federal Street, Billerica, MA 01821 Bay Networks Software License This Software

Using Technician Interface Scripts1-8Using Script CommandsThis section provides an overview of the show and enable/disable commands. To present a cont

Using Technician Interface Scripts2-248versionDisplays the current version number and modification date for the e1.bat script.Sample Display – show e1

show egp2-249show egpThe show egp <option> commands display information about the Exterior Gateway Protocol (EGP). For detailed information abou

Using Technician Interface Scripts2-250neighborsDisplays information about each of the neighbors configured for this router. The table includes the fol

show egp2-251statsDisplays statistical information for EGP. The table includes the following information:Sample Display – show egp statsEGP Statistics

Using Technician Interface Scripts2-252show fddiThe show fddi <option> commands display information about Fiber Distributed Data Interface (FDDI

show fddi2-253alertsDisplays all FDDI modules that are enabled but not up. Use this display to identify the interfaces that are not working. The table

Using Technician Interface Scripts2-254Sample Display – show fddi alertsFDDI Modules on Alert:----------------------

show fddi2-255disabledDisplays FDDI circuits that a user has manually disabled. For definitions of the columns in the table, see the alerts command. In

Using Technician Interface Scripts2-256hwfiltersDisplays status and statistical information about the hardware filters in use, if any. The table include

show fddi2-257mac [circuit <circuit name>]Displays the Media Access Control (MAC) parameters for all circuits or for a specific circuit. This dis

Using Technician Interface Scripts1-9AppleTalk Update-based Routing Protocol service (connection, statistics, zone filters)show aurp <option>Auto

Using Technician Interface Scripts2-258Sample Display – show fddi macFDDI Modules MAC Parameters:---------------------------- Ups

show fddi2-259portDisplays FDDI port attributes. The table includes the following information:Slot Slot identifier associated with the port. Conn Conne

Using Technician Interface Scripts2-260Sample Display – show fddi portFDDI Modules Port Parameters:----------------------------

show fddi2-261Sample Display – show fddi receiveFDDI Module Receive Errors:--------------------------- CRC Overrun Invalid

Using Technician Interface Scripts2-262Sample Display – show fddi sampleFDDI Sampled Data over 10 seconds----------------------------------

show fddi2-263Connection Policy Table that represents the requested connection possibilities for this node. Each column identifies whether a connection

Using Technician Interface Scripts2-264Sample Display – show fddi smtFDDI Modules SMT Parameters:---------------------------- Connec

show fddi2-265stats [circuit <circuit name>]Displays FDDI input/output statistical information for all FDDI modules or for a specific circuit. Th

Using Technician Interface Scripts2-266Sample Display – show fddi system errorsFDDI Module System Errors:----------------------------

show fddi2-267Sample Display – show fddi transmitFDDI Module Transmit Errors:---------------------------- Aborted UnderrunSlot Co

Using Technician Interface Scripts1-10High Speed Serial Interface service (receive, transmit, and system errors; sample data; statistics)show hssi &

Using Technician Interface Scripts2-268show frThe show fr <option> commands display configuration, state, and statistical information about Frame

show fr2-269Sample Display – show fr alerts Frame Relay DLCMI ALERT Table ----------------------------- Line.LLIndex Circuit Mgt Type Status F

Using Technician Interface Scripts2-270disabledDisplays the interfaces that are currently disabled. For column definitions, see the alerts command.Samp

show fr2-271lines [<line> | <line.llindex>]Displays information about all or some of the Frame Relay lines configured on the router.The t

Using Technician Interface Scripts2-272pvcs [<line> | <line.llindex> | <line.llindex.DLCI>]Displays information about all or sel

show fr2-273Sample Display – show fr pvcsFrame Relay PVC Table--------------------- Line.LLIndex.DLCI State Type Mode Congestion S

Using Technician Interface Scripts2-274Sample Display – show fr stats Frame Relay PVC Statistics --------------------------

show fr2-275versionDisplays the current version number and modification date of the fr.bat script.Sample Display – show fr version Frame Relay Version

Using Technician Interface Scripts2-276show ftpThe show ftp <option> commands display configuration and statistical information about the Bay Net

show ftp2-277Sample Display – show ftp baseFTP Base Information--------------------- Default Idle Protocol State Volume

Using Technician Interface Scripts1-11Point-to-Point Protocol service (AppleTalk, bad packets, Bridge, CHAP, circuits, DECnet, IP, IPX, line, LQR, OSI

Using Technician Interface Scripts2-278Sample Display – show ftp statsFTP Statistics Information-------------------------- Logins Files

show hardware2-279show hardwareThe show hardware <option> commands display information about a router’s hardware.The show hardware command suppo

Using Technician Interface Scripts2-280Sample Display – show hardware backplaneHardware Backplane Information------------------------------

show hardware2-281config_fileDisplays the configuration file used to boot the router or reset a slot. The table shows the name and volume that was the sou

Using Technician Interface Scripts2-282Sample Display – show hardware image Active Image Information ------------------------ Slot File Name

show hardware2-283proms [<slot number>]Displays PROM information for all slots or for a specific slot. The table includes the revision and build

Using Technician Interface Scripts2-284Sample Display – show hardware slots Hardware Information per Slot ----------------------------- Process

show hardware2-285Sample Display – show hardware slots Hardware Information per Slot ----------------------------- Processor Processor Pro

Using Technician Interface Scripts2-286show hssiThe show hssi <option> commands display configuration, status, and statistical information about

show hssi2-287State State of the line driver, as follows:• BOFLwait – Driver is waiting for its own Breath-of-Life frames to be successfully transmitt

Using Technician Interface Scripts1-12Using the enable and disable CommandsYou can use the enable or disable commands from the Technician Interface co

Using Technician Interface Scripts2-288Sample Display – show hssi alertsHSSI Modules on Alert:----------------------

show hssi2-289Sample Display – show hssi disabledHSSI Modules Disabled:---------------------- BOFL

Using Technician Interface Scripts2-290Sample Display – show hssi receive errorsHSSI Module Receive Errors:-----------------------------

show hssi2-291Sample Display – show hssi sampleHSSI Sampled Data over 10 seconds---------------------------------- Rx Tx

Using Technician Interface Scripts2-292Sample Display – show hssi statsHSSI Module I/O Statistics:--------------------------- Receiv

show hssi2-293Sample Display – show hssi system errorsHSSI Module System Errors:-------------------------- Rx Ring Tx Ring Int

Using Technician Interface Scripts2-294versionDisplays the current version number and modification date of the hssi.bat script.Sample Display – show hs

show igmp2-295show igmpThe show igmp <option> commands display configuration, state, and statistical information about the Internet Gateway Manag

Using Technician Interface Scripts2-296Sample Display – show igmp baseIGMP Base Information---------------------- Protocol State -------- ----

show igmp2-297Sample Display – show igmp circuitsIGMP Circuits-------------- Circuit State Query Rate DR Timeout MembershipTimeout ------

Using Technician Interface Scripts1-13AppleTalk Update-based Routing Protocol (connection)enable/disable aurp <option>Automatic line speed negot

Using Technician Interface Scripts2-298stats [<circuit name>]Displays statistics for all IGMP circuits or a specified IGMP circuit. The table dis

show ip2-299show ipThe show ip <option> commands display configuration, state, and statistical information about the Internet Protocol (IP). For

Using Technician Interface Scripts2-300adjacent hostsDisplays a table of configured adjacent hosts. The table includes the following information:rip di

show ip2-301Sample Display – show ip adjacent hostsIP Adjacent Hosts----------------- Host IP Addr Interface IP Interface Mask Mac Address

Using Technician Interface Scripts2-302Sample Display – show ip arpIP ARP Table------------ IP Address Physical Address Type -------------

show ip2-303The base command also displays the number of networks and hosts that IP knows about and the number of policy rules defined.Sample Display –

Using Technician Interface Scripts2-304Sample Display – show ip circuitsIP Circuits----------- Circuit Circuit # State IP Address --------

show ip2-305Sample Display – show ip enabledIP Circuits----------- Circuit Circuit # State IP Address -------- ----------- -------- ------

Using Technician Interface Scripts2-306Sample Display – show ip rfilters export BGP3IP BGP3 Export Filters:-----------------------

show ip2-307Sample Display – show ip ripIP RIP Information------------------ IP Interface State Supply Listen ---------------- -----

Using Technician Interface Scripts1-14LAN Network manager (base, circuit)enable/disable lnm <option>NetBIOS over IP (base, interface) enable/dis

Using Technician Interface Scripts2-308rip disabledDisplays the IP interfaces that have RIP configured but disabled. For more information on column defi

show ip2-309routes [-A] [type {local|bgp|egp|ospf|rip}] | [<IP address> | find <search pattern>]Displays IP routes. You can use the followi

Using Technician Interface Scripts2-310Sample Display – show ip routesIP Routes---------Network/Mask Proto Age Slot Cost NextHop Ad

show ip2-311ip routes -A------------ Network/Mask Proto Age Sl Cost NextHop Address / AS Weight ------------------- ------ -------

Using Technician Interface Scripts2-312Sample Display – show ip staticIP Static Routes---------------- IP Destination Network Mask Cost N

show ip2-313Sample Display – show ip statsIP Statistics------------- In Out In Out Circuit I

Using Technician Interface Scripts2-314stats datagrams [<circuit name>]Displays error statistics about IP datagrams that IP has processed for al

show ip2-315stats fragments [<circuit name>]Displays all information about fragmented IP packets or information for all interfaces or for a spec

Using Technician Interface Scripts2-316stats icmp client [<circuit name>]Displays echo, timestamp, and address mask statistics about Internet Co

show ip2-317Sample Display – show ip stats icmp inIP ICMP In Statistics--------------------- ICMP ICMP In Destintn Rcv.T

Using Technician Interface Scripts1-15Using the Menu UtilityYou can choose scripts from menus rather than starting them from the Technician Interface

Using Technician Interface Scripts2-318Sample Display – show ip stats icmp miscICMP Miscellaneous Statistics -----------------------------

show ip2-319stats icmp server [<circuit name>]Displays statistics about ICMP messages that the router generates. For column definitions in the di

Using Technician Interface Scripts2-320Sample Display – show ip stats security inIP Security In Statistics-------------------------

show ip2-321Sample Display – show ip stats security outIP Security Out Statistics-------------------------- Drop Tx Drop Tx

Using Technician Interface Scripts2-322versionDisplays the version number and date for the ip.bat script.Sample Display – show ip versionIP.bat Versio

show ipx2-323show ipxThe show ipx <option> commands display information about Novell’s Internet Packet Exchange (IPX) services on a Bay Networks

Using Technician Interface Scripts2-324adjacent hostsDisplays the configurable parameters for all statically configured adjacent hosts. The IPX Adjacent

show ipx2-325Sample Display – show ipx adjacent hostsIPX Adjacent Host Table Information----------------------------------- Circuit IPX

Using Technician Interface Scripts2-326Sample Display – show ipx alertsIPX Circuit Configuration Information (Alerts)---------------------------------

show ipx2-327There is also a base record statistical table displayed that includes total routes, services, and hosts for the protocol.Sample Display –

Using Technician Interface Scripts1-16The Main Menu appears on your screen: Main Menu D. Disable MORE. M. Menu c

Using Technician Interface Scripts2-328base statsDisplays base record statistics for the IPX protocol. The statistics provide information on the total

show ipx2-329Sample Display – show ipx circuitsIPX Circuit Configuration Information (ALL)-------------------------------------------circuit State

Using Technician Interface Scripts2-330Sample Display – show ipx disabledIPX Circuit Configuration Information (Disabled)-----------------------------

show ipx2-331forwardDisplays the entries in the IPX forwarding table, which includes the following information.Sample Display – show ipx forwardIPX Fo

Using Technician Interface Scripts2-332Sample Display – show ipx hostsIPX Host Table Information--------------------------Host Addr Ckt Idx Netw

show ipx2-333Sample Display – show ipx ping ADMIN_SERVERIPX Ping command, by name-------------------------Searching for ADMIN_SERVER in server databas

Using Technician Interface Scripts2-334Sample Display – show ipx ripIPX RIP Interface Record Configuration Information (All)--------------------------

show ipx2-335rip disabledDisplays IPX RIP interfaces that are disabled. For column definitions, see the rip command.Sample Display – show ip rip disabl

Using Technician Interface Scripts2-336route filtersDisplays the IPX Route Filter Information table, which contains the following information:Sample Di

show ipx2-337routes [type {direct | nlsp | rip | static} | <IP address> | find <search pattern> | net <search pattern> | host <

Using Technician Interface Scripts1-17To display a submenu, enter the number of your choice. For example, to display the IP menu, enter 25 at the prom

Using Technician Interface Scripts2-338Sample Display – show ipx routesIPX Routing Table Information-----------------------------Dest Net Ckt Idx Nx

show ipx2-339Sample Display – show ipx routes type localIPX Routing Table Information-----------------------------Dest Net Ckt Idx NxtHop Net NextH

Using Technician Interface Scripts2-340Sample Display – show ipx route net 0x2E0252* IPX Routing Table Information-----------------------------Dest Ne

show ipx2-341Sample Display – show ipx sapIPX SAP Interface Record Configuration Information (All)----------------------------------------------------

Using Technician Interface Scripts2-342sap alertsDisplays IPX SAP interfaces whose Disable/Enable parameter conflicts with their state. For column defin

show ipx2-343sap enabledDisplays IPX SAP interfaces that are enabled. For column definitions, see the sap command.Sample Display – show ipx sap enabled

Using Technician Interface Scripts2-344Sample Display – show ipx server name level filtersIPX Server Name Level Filter Information---------------------

show ipx2-345Sample Display – show ipx server net level filtersIPX Server Net Level Filter Information--------------------------------------- Circuit

Using Technician Interface Scripts2-346services [<name search pattern> | type <hex search pattern> | Net <name search pattern>]Displ

show ipx2-347Sample Display – show ipx servicesIPX Service Table Information----------------------------- Server

Bay Networks, Inc. 4401 Great America Parkway, Santa Clara, CA 950548 Federal Street, Billerica, MA 01821 Bay Networks Software License (continued)

Using Technician Interface Scripts1-18When you press Enter, the menu utility returns to the submenu; in this example, pressing Enter displays the IP M

Using Technician Interface Scripts2-348Sample Display – show ipx service type *4IPX Service Table Information-----------------------------

show ipx2-349Sample Display – show ipx service net *00010?IPX Service Table Information----------------------------- Server

Using Technician Interface Scripts2-350static routesDisplays all configured Static Routes. The table includes the following information:Sample Display

show ipx2-351Sample Display – show ipx static servicesIPX Static Service Table Information------------------------------------

Using Technician Interface Scripts2-352statsDisplays general forwarding statistics for IPX interfaces. The table includes the following information:Ci

show ipx2-353Sample Display – show ipx statsIPX Statistical Information--------------------------- Circuit IPX In In Out

Using Technician Interface Scripts2-354Sample Display – show ipx stats datagramsIPX Statistical Datagram Information----------------------------------

show ipx2-355Sample Display – show ipx traffic filterIPX Traffic Filter Information------------------------------ Circuit IPX

Using Technician Interface Scripts2-356show iredundThe show iredund <option> commands display information about the Interface Redundancy protoco

show iredund2-357Sample Display – $show iredund circuitInterface Redundancy Circuit Table -------------------------------Circuit Slot Port

Using Technician Interface Scripts1-19 Main MenuEnter menu number or TI command: To turn menu control

Using Technician Interface Scripts2-358enabledDisplays all enabled circuits that contain an interface redundancy port. A circuit is enabled if the dis

show isdn2-359show isdnThe show isdn <option> commands display information about the Integrated Services Digital Network (ISDN) service. For inf

Using Technician Interface Scripts2-360alertsDisplays all enabled circuits that are not active. Use this display to identify the ports that are not wo

show isdn2-361Sample Display – show isdn calls generalISDN Active Call Information---------------------------- DSL B Called

Using Technician Interface Scripts2-362inphoneDisplays the configuration set up for incoming phone numbers. The table displays the following informatio

show isdn2-363localLists the local phone number entry for each line in the line pool. The display includes the following information:Sample Display –

Using Technician Interface Scripts2-364messages receivedDisplays the number of messages the router received on each ISDN line. The table displays the

show isdn2-365Sample Display – show isdn messages sentISDN Messages Sent------------------ Setup Connect Disconn. Clear Activ. Dea

Using Technician Interface Scripts2-366Sample Display – show isdn poolsPool Line Pool Channel ChannelsType Number ID CountPriorityIn Use --------- ---

show isdn2-367Sample Display – show isdn switchISDN Switch Configuration------------------------- Incoming Slot Switch Ty

Using Technician Interface Scripts1-20Adding a CommandWith menu control on, add a command by entering a at the Enter menu number or TI command: prom

Using Technician Interface Scripts2-368show isdn briThe show isdn bri <option> commands display information about the ISDN Basic Rate Interface

show isdn bri2-369alertsDisplays all enabled circuits that are not active. Use this display to identify the ports that are not working. The table incl

Using Technician Interface Scripts2-370baseDisplays base record information for all ISDN BRI circuits or for a specified circuit. For definitions of th

show isdn bri2-371enabledDisplays circuits that a user has enabled. In this case, State is Down, Init, Not Present, or Up. For definitions of the colum

Using Technician Interface Scripts2-372sample [<period in seconds>] [circuit <circuit name>]Displays the ISDN BRI statistics generated dur

show isdn bri2-373Sample Display – show isdnbri statsISDN BRI Module I/O Statistics:-------------------------------Receive Receive Transmit Transmit T

Using Technician Interface Scripts2-374transmit errorsDisplays statistical information about transmission errors for all circuits or for a specific cir

show lane2-375show laneThe show lane <options> command displays information about ATM LAN Emulation. For details about the Bay Networks implemen

Using Technician Interface Scripts2-376Sample Display – show lane clientsATM LAN Emulation Client Running Config Info---------------------------------

show lane2-377Sample Display – show lane configATM LAN Emulation Client Table------------------------------ Cct# Circuit Name LAN Name LAN T

Using Technician Interface Scripts1-21 Main MenuEnter menu number or TI command: 1. APPN 22. FT

Using Technician Interface Scripts2-378Entry Type Indicates how this table entry was created: LEARNED, LEARNED CTRL, LEARNED DATA, STATIC VOL, STATIC

show lane2-379Sample Display – show lane learpATM mulation Client MAC-to-ATM ARP Cache--------------------------------------------- Cct# Circuit

Using Technician Interface Scripts2-380mac [<circuit name>]Displays ATM LAN Emulation Client MAC address information for all circuits, or for a

show lane2-381Cct# Circuit number of the LEC.Circuit Name Circuit name that Site Manager assigned.Config Direct Line# Interface associated with the Con

Using Technician Interface Scripts2-382Sample Display – show lane serversATM LAN Emulation Client Server VCC Table------------------------------------

show lane2-383Sample Display – show lane statsATM LAN Emulation Client Statistics----------------------------------- Cct# Circuit Name Req Ou

Using Technician Interface Scripts2-384show lapbThe show lapb <option> commands display information about the Link Access Procedure-Balanced (LA

show lapb2-385Sample Display – show lapb alertsLAPB ALERT Table---------------- FRMR Rejects RNR Setups Abnormal Ret

Using Technician Interface Scripts2-386enabledDisplays LAPB lines that are configured and enabled. For definitions of column headings, see the disabled

show lapb2-387Sample Display – show lapb line 201101LAPB Line Information Table---------------------------Line.LLIndex Circuit Station Type Window Si

Using Technician Interface Scripts1-22Deleting a CommandWith menu control on, delete a command by entering d at the Enter menu number or TI command: p

Using Technician Interface Scripts2-388The table includes the following information:Sample Display – show lapb stats 201101LAPB Line Statistics-------

show lnm2-389show lnmThe show lnm <option> commands display information about services that LNM Servers provide. For detailed information about

Using Technician Interface Scripts2-390Sample Display – show lnm alertsLNM Servers Circuit Alerts--------------------------Circuit LNM LNM LRM

show lnm2-391Sample Display – show lnm baseLNM Servers Base Information----------------------------Protocol State ----------- --------LNM Server

Using Technician Interface Scripts2-392Sample Display – show lnm cannotlinkLNM Servers Cannot Link----------------------- Internal

show lnm2-393Sample Display – show lnm cannotlink circuitLNM Servers Cannot Link Circuit-------------------------------

Using Technician Interface Scripts2-394Sample Display – show lnm circuitLNM Servers Circuit Information-------------------------------Circuit LNM

show lnm2-395The circuit record configuration display includes the following information:Sample Display – show lnm configurationLNM Servers Base Configu

Using Technician Interface Scripts2-396disabledDisplays the LNM Servers circuits and servers that a user has manually disabled. The table includes the

show lnm2-397Sample Display – show lnm enabledLNM Servers Circuits Enabled-----------------------------Circuit LNM LNM LRM LNM LBS LNM REM

Using Technician Interface Scripts1-23The Main Menu automatically refreshes, displaying a new menu with the new menu title.

Using Technician Interface Scripts2-398passwords [<circuit name>]Displays the passwords currently configured for all LNM Servers circuits or for

show nbip2-399show nbipThe show nbip <option> commands display configuration and statistical information about NetBIOS over IP services. For deta

Using Technician Interface Scripts2-400interfacesDisplays information about each interface:Sample Display – show nbip interfacesNBIP Interfaces-------

show nbip2-401namesDisplays name cache information:Sample Display – show nbip namesNBIP Name Cache---------------NetBIOS Name IP Address L

Using Technician Interface Scripts2-402show nmlThe show nml <option> commands display configuration and statistical information about Native Mode

show nml2-403Sample Display – show nml circuitsNML Circuit Table----------------- CUG Security SAID SecurityCircui

Using Technician Interface Scripts2-404Sample Display – show nml seclistsNML Security Lists------------------ Circuit Port Status Action

show nml2-405Sample Display – show nml statsBridge Statistics ----------------- Circuit Port Discards-------- -------- --------F31 1

Using Technician Interface Scripts2-406show osiThe show osi <option> commands display configuration, state, and statistical information about Ope

show osi2-407Sample Display – show osi adjacencyOSI Dynamic Adjacency Information------------------------------------ Circuit Adjacent ID State N

Using Technician Interface Scripts1-24Editing a Menu TitleWith menu control on, edit a menu title by entering h at the Enter menu number or TI comman

Using Technician Interface Scripts2-408Sample Display – show osi baseOSI Base Record Information--------------------------- Protocol State Area Ad

show osi2-409Sample Display – show osi circuits e31OSI Circuit Information----------------------- Circuit State Forwarding ------- ---------

Using Technician Interface Scripts2-410level1 routes [find <destination sys ID>]Displays information from the level 1 routing table for all entri

show osi2-411Sample Display – show osi level2 routesOSI Level II Routing Information-------------------------------- Destination SysId Next

Using Technician Interface Scripts2-412stats clnpDisplays statistics for the ConnectionLess Network Protocol (CLNP) packets on each OSI circuit. The t

show osi2-413Sample Display – show osi stats errorsOSI Error Statistics-------------------- Init Rejected Bad Bad Bad B

Using Technician Interface Scripts2-414 show ospf The show ospf <option> commands display state, configuration, and statistical information

show ospf2-415 Sample Display – show ospf area OSPF Area Information--------------------- Stub Area Id State Area Authe

Using Technician Interface Scripts2-416 Sample Display – show ospf ase OSPF AS External Routes----------------------- Link Originating

show ospf2-417 interface Displays a table of OSPF interfaces. The table includes the following information: IP Address Internet address of the OSPF i

Using Technician Interface Scripts1-25 Protocol Statistics Enter menu number or TI command:

Using Technician Interface Scripts2-418 Sample Display – show ospf interface OSPF Interfaces---------------

show ospf2-419 Sample Display – show ospf lsdb OSPF LSDB---------OSPF Area: 0.0.0.0 LS Type Link State ID Adv Router E Metric ASE Fwd Ad

Using Technician Interface Scripts2-420 Sample Display – show ospf neighbors OSPF Neighbors-------------- Neighbor

show ospf2-421 version Displays the current version number and modification date of the ospf.bat script. Sample Display – show ospf version OSPF.bat

Using Technician Interface Scripts2-422 show packet The show packet <option> commands display configuration and status information about Pac

show packet2-423 Sample Display – show packet alerts Packet Capture Line Information (Alerts)----------------------------------------Line Number St

Using Technician Interface Scripts2-424 Sample Display – show packet capture 102101 Pkt# 1 06/24/94 06:59:03.018 CSMACD 52 Tx00000000: 01 8

show packet2-425 RxTrigger Trigger type for receive when the capture buffer is full or a match on a trigger filter occurs: Buffer full, Match filter1,

Using Technician Interface Scripts2-426 RxFltr2Ref Reference point in the packet for the offset, as follows:• MAC – First byte of the packet.• Data

show packet2-427Sample Display – show packet configuration 102101 Packet Capture Configuration for Line 102101 ----------------------------------

Using Technician Interface Scripts1-26Loading a New MenuWith menu control on, load a new menu by entering l at the Enter menu number or TI command: p

Using Technician Interface Scripts2-428disabledDisplays packet capture lines that a user has manually disabled. State is one of the following:Sample D

show packet2-429linenumbersDisplays the line numbers configured for packet capture. The table shows the following information:Sample Display – show pac

Using Technician Interface Scripts2-430status [<line number>]Displays the status of the lines configured for packet capture. You can display all

show ping2-431show pingThe show ping <option> commands display information about the Bay Networks Ping MIB service, which provides a means for t

Using Technician Interface Scripts2-432Sample Display – show ping config IP Address Size Retry Timeout Status -------------

show ping2-433Sample Display – show ping history Round Min Round Max Round Avg RoundIP Address Received Dropp

Using Technician Interface Scripts2-434traceroutesDisplays the hops between the source address and the specified destination address. Sample Display –

show ping2-435version Displays the current version number and date of the ping.bat script.Sample Display – show ping versionPING.bat Version: 1.1 Date

Using Technician Interface Scripts2-436show pppThe show ppp <option> commands display Point-to-Point Protocol (PPP) line and state information,

show ppp2-437alertsDisplays all protocols that are enabled but whose state is not opened. The display includes the following information:Circuit Name

Using Technician Interface Scripts1-27 Main Menu 1. menu appn.mnu 22. menu ftp.mnu 43. menu smds.mnu 2. me

Using Technician Interface Scripts2-438Sample Display – show ppp alertsPPP: ALERTS----------- Circuit Protocol State -------- ---------- --------

show ppp2-439Sample Display – show ppp appletalk configPPP: APPLETALK NCP Configured Information-----------------------------------------

Using Technician Interface Scripts2-440bad packetsDisplays the number of bad packets received over each circuit and the first 16 bytes of the last bad

show ppp2-441Sample Display – show ppp bridge configPPP: BRIDGE NCP Configured Information-------------------------------------- Bri

Using Technician Interface Scripts2-442chap {local | remote}The displays for the local and remote include the following information:Sample Display – s

show ppp2-443Sample Display – show ppp chap remotePPP Line: Remote CHAP Configuration----------------------------------- Line. LCP

Using Technician Interface Scripts2-444Sample Display – show ppp circuits[2:1]$ show ppp circuitsPPP Circuit Information----------------------- PPP ov

show ppp2-445decnetDisplays the state of DECnet NCP on all circuits on which PPP is configured. State is either Disabled, or if Enabled, any of the sta

Using Technician Interface Scripts2-446enabledDisplays the state of all NCPs enabled on each circuit. States are listed under the alerts command.Sampl

show ppp2-447Sample Display – show ppp ipPPP: IP NCP Information------------------------ Local Local Remote R

v Contents About This Guide Software Suites ...

Using Technician Interface Scripts1-28PPP subcommand menu with menu control OFF/disabled: PPP Menu 1. Alerts 1

Using Technician Interface Scripts2-448Sample Display – show ppp ipx configPPP: IPX NCP Configured Information------------------------------------

show ppp2-449Sample Display – show ppp ipx name localPPP: IPX NCP Local Router Name------------------------------ Circuit State Lo

Using Technician Interface Scripts2-450line {configuration | parameters}The display includes the following information:configuration Displays the configu

show ppp2-451Sample Display – show ppp line configPPP Line Configuration---------------------- Line. LCP Restart Echo-Req Echo-Rep Maxi

Using Technician Interface Scripts2-452Sample Display – show ppp line paramPPP Line: Parameter Information------------------------------- Li

show ppp2-453Sample Display – show ppp lqr configPPP Line: Line Quality Reporting Configuration----------------------------------------------

Using Technician Interface Scripts2-454Sample Display – show ppp lqr statsPPP Line: Line Quality Reporting Stats--------------------------------------

show ppp2-455Sample Display – show ppp multilink informationPPP Multilink Information------------------------- Bundle

Using Technician Interface Scripts2-456Sample Display – show ppp multilink circuitsPPP Multilink Circuits----------------------

show ppp2-457pap {local | remote}The display includes the following information:Sample Display – show ppp pap localPPP Line: Local PAP Configuration--

Using Technician Interface Scripts1-29PPP subcommand menuToggled to display subcommands instead of subcommand functions:

Using Technician Interface Scripts2-458The display includes the following information:Sample Display – show ppp pap remotePPP Line: Remote PAP Configu

show ppp2-459Sample Display – show ppp state PPP State Information--------------------- PPP over Sync Driver ---------------------

Using Technician Interface Scripts2-460If your two circuit entries have the same name, one of them is a primary circuit and the other is a backup circ

show ppp2-461vinesDisplays the state of the VINES NCP for all circuits on which PPP is configured. State is either Disabled, or if Enabled, any of the

Using Technician Interface Scripts2-462Sample Display – show ppp wcp[2:1]$ show ppp wcpPPP: WCP NCP Information------------------------ Circuit Stat

show process2-463show processThe show process <option> commands display information about the use of resources (buffers, cpu, memory, lists, etc

Using Technician Interface Scripts2-464Sample Display – show process buffers total Total Buffer Use Statistics --------------------------- Sl

show process2-465cpuDisplays the use in 100ths of seconds and percentage of cpu used by all processes on the router. By specifying the options that ap

Using Technician Interface Scripts2-466memoryDisplays the number and percentage of memory used by all processes on the router. The output can be tailo

show process2-467listDisplays a list of all the processes that are or may have run on the router since boot time. The show process list command suppo

Using Technician Interface Scripts2-468show protopriThe show protopri <option> commands display information about DLSw protocol prioritization q

show protopri2-469Sample Display – show protopri cc_statsProtocol Priority Congestion Control Statistics ---------------------------------------------

Using Technician Interface Scripts2-470Sample Display – show protopri filtersProtocol Priority Traffic Filters ---------------------------------

show protopri2-471versionDisplays the current version number and modification date of the protopri.bat script.Sample Display – show protopri version pr

Using Technician Interface Scripts2-472show rarpThe show rarp <option> commands display information about Reverse Address Resolution Protocol (R

show rarp2-473circuits [<circuit name>]Displays information about all RARP circuits or for a specific circuit. The table includes the circuit nam

Using Technician Interface Scripts2-474enabledDisplays all enabled RARP circuits. In this case, State is Enabled. The table also includes the name of

show rptr2-475show rptrThe show rptr <option> commands display configuration, status, and statistical information about Bay Networks Access Node

Using Technician Interface Scripts2-476Sample Display – show rptr info last_addr802.3 Repeater(HUB) Port Last Source Address Information:-------------

show rptr2-477Sample Display – show rptr sampleALL Repeater Ports Statistics Sampled Data over 10 seconds--------------------------------------------

2-1Chapter 2Using the show CommandUse the show command to display routing, configuration, interface, and statistical data from the Management Informati

Using Technician Interface Scripts2-478Sample Display – show rptr sample 3 port 12Repeater Port Statistics Sampled Data over 3 seconds--------------

show rptr2-479Sample Display – show rptr stats802.3 Repeater (HUB) Statistics:--------------------------------Port Readable Readable Total

Using Technician Interface Scripts2-480Sample Display – show rptr stats all802.3 Repeater (HUB) Statistics:--------------------------------- Re

show rptr2-481Sample Display – show rptr stats totals802.3 Repeater (HUB) Statistics Totals:--------------------------------------- Repeater To

Using Technician Interface Scripts2-482Sample Display – show rptr stats errors802.3 Repeater (HUB) Error Statistics:----------------------------------

show rptr2-483Sample Display – show repeater status ports802.3 Repeater (HUB) Ports Status:---------------------------------- Port Admin

Using Technician Interface Scripts2-484show rredundThe show rredund <option> commands display information about router redundancy. For detailed

show rredund2-485baseDisplays the base record information for router redundancy. The base record controls router redundancy for the entire system. The

Using Technician Interface Scripts2-486Sample Display – show rredund baseRouter Redundancy Base Record Information -----------------------------------

show rredund2-487Sample Display – $show rredund circuitsRouter Redundancy Circuit Table ------------------------------- Circuit Port State

Using Technician Interface Scripts2-2show appnThe show appn <option> commands display configuration, state, and statistical information about the

Using Technician Interface Scripts2-488Sample Display – show rredund enableRouter Redundancy Circuit Table ------------------------------- Circuit

show rredund2-489Sample Display – $show rredund remoteRouter Redundancy Remote Members -------------------------------- Group ID Member ID IP Addr

Using Technician Interface Scripts2-490roleDisplays the roles of known members of this redundancy group, from the point of view of this router. The

show rredund2-491Sample Display – $show rredund sonmpRouter Redundancy SONMP Stats ----------------------------- Circuit Circuit Transmit Receiv

Using Technician Interface Scripts2-492show rscThe show rsc <option> commands display information about managed line resources. The Bay Networks

show rsc2-493Sample Display – show rsc bandTX Line Resources: Reserved Bandwidth Statistics------------------------------------------------

Using Technician Interface Scripts2-494Sample Display – show rsc resTX Line Resources: Reserved Flow Statistics---------------------------------------

show rsc2-495Sample Display – show rsc unresTX Line Resources: Unreserved Traffic Statistics------------------------------------------------

Using Technician Interface Scripts2-496show sdlcThe show sdlc <option> commands display information about the Synchronous Data Link Control (SDL

show sdlc2-497circuits [<circuit number>]Displays SDLC configuration information for all circuits or for a specific circuit. The table contains t

show appn2-3dlus [<DLUS name>] rtp statisticsendpoint address [<PLU name>] topology node [<CP name>]endpoint route [<PLU name>

Using Technician Interface Scripts2-498disabledDisplays all disabled SDLC interfaces. For more information on column definitions, see the circuits comm

show sdlc2-499stats [<circuit number>]Displays statistical information for all circuits or for a specified circuit. The table includes the follo

Using Technician Interface Scripts2-500show smds The show smds <option> commands display configuration, status, and statistical information about

show smds2-501Sample Display – show smds addresses SMDS Circuit Address Table -------------------------- Circuit Individual Address Group Address

Using Technician Interface Scripts2-502Sample Display – show smds circuitSMDS Circuit Interface Table----------------------------Circuit State Pol

show smds2-503Sample Display – show smds disabledSMDS Disabled Table------------------------Circuit Mode State ------- -------- --------S22

Using Technician Interface Scripts2-504versionDisplays the current version number and modification date of the smds.bat script.Sample Display – show sm

show snmp2-505show snmpThe show snmp <option> commands display status, configuration, and performance information about the Simple Network Manage

Using Technician Interface Scripts2-506Sample Display – show snmp baseSNMP Base Information--------------------- Packets P

show snmp2-507Sample Display – show snmp communitySNMP Community Information-------------------------- Community Community Community Index

Using Technician Interface Scripts2-4adjacencies [<node name>]Displays the following information for all APPN nodes or for a specific APPN node:S

Using Technician Interface Scripts2-508entity traps [find entity <entity number> | name <entity name> | slot <slot number>]Display

show snmp2-509Sample Display – show snmp entity trapsSNMP Entity Trap Information---------------------------- Entity Slot

Using Technician Interface Scripts2-510Sample Display – show snmp exceptionsSNMP Exception Information--------------------------- Entity Event

show span2-511show span The show span <option> commands display information about Spanning Tree Bridge services. For detailed information about

Using Technician Interface Scripts2-512Sample Display – show span alertsSpanning Tree Circuit Alert Information---------------------------------------

show span2-513Sample Display – show span baseSpanning Tree Base Record Information-------------------------------------

Using Technician Interface Scripts2-514configurationDisplays Spanning Tree global configuration parameters. These parameters are all user configurable. T

show span2-515Sample Display – show span configuration circuitsSpanning Tree Circuit Configuration Parameters------------------------------------------

Using Technician Interface Scripts2-516enabledDisplays Spanning Tree circuits that are currently enabled. For definitions of the columns in the table,

show span2-517versionDisplays the current version number and date of the span.bat script.Sample Display – show span versionSPAN.bat Version: 1.15 Date

show appn2-5baseDisplays base record information for APPN. The table displays the following information:Capabilities:Capacity:Negotiated LS Support In

Using Technician Interface Scripts2-518show srThe show sr <option> commands display information about Source Routing interfaces. For detailed in

show sr2-519Sample Display – show sr alertsSource Routing (SR) Interface Information ----------------------------------------- Circuit Mode Stat

Using Technician Interface Scripts2-520Sample Display – show sr bridgesSource Routing (SR) Bridge IDs------------------------------

show sr2-521Sample Display – show sr configuration Source Routing (SR) Base Record Configuration ---------------------------------------------

Using Technician Interface Scripts2-522Sample Display – show sr configuration circuitSource Routing (SR) Interface Record Configuration----------------

show sr2-523Sample Display – show sr enabledSource Routing (SR) Interface Information----------------------------------------- Circuit Mode Stat

Using Technician Interface Scripts2-524Sample Display – show sr ip alertsSample Display: Source Route IP Encapsulation (SR IP) Interface Information--

show sr2-525Sample Display – show sr ip circuitsSource Route IP Encapsulation (SR IP) Circuit Information---------------------------------------------

Using Technician Interface Scripts2-526Sample Display – show sr ip configuration circuitSource Route IP Encapsulation (SR IP) Circuit Record Configurat

show sr2-527Sample Display – show sr ip enabledSource Route IP Encapsulation (SR IP) Circuit Information----------------------------------------------

Using Technician Interface Scripts2-6Sample Display – show appn baseAPPN Base Information--------------------- Node Name: USWFLT01.DURHAM State:

Using Technician Interface Scripts2-528Sample Display – show sr ip routesSource Route IP Encapsulation (SR IP) Routes---------------------------------

show sr2-529statsDisplays all Source Routing interface statistics or statistics for a specific circuit. The table includes the following information:Sa

Using Technician Interface Scripts2-530show srspanThe show srspan <option> commands display information about Source Route Spanning Tree Bridge

show srspan2-531Sample Display – show srspan alertsSource Route Spanning Tree Circuit Alert Information-----------------------------------------------

Using Technician Interface Scripts2-532Sample Display – show srspan baseSource Route Spanning Tree Base Record Information----------------------------

show srspan2-533Sample Display – show srspan configurationSource Route Spanning Tree Configuration Table----------------------------------------------

Using Technician Interface Scripts2-534circuits [<circuit name>]Displays source route Spanning Tree circuit information. For definitions of the

show srspan2-535enabledDisplays source route Spanning Tree circuits that are currently enabled. For definitions of the columns in the table, see the al

Using Technician Interface Scripts2-536versionDisplays the current version number and date of the srspan.bat script.Sample Display – show srspan versi

show st22-537show st2The show st2 <option> commands display information about the ST2 protocol and services. For detailed information on the Bay

show appn2-7cos node [<COS name>]Displays resistance and congestion information for all COS types or for a specific COS type. COS COS Name: #BAT

Using Technician Interface Scripts2-538circuits [<circuit name>]Displays information for all ST2 circuits or for a specific circuit. The table in

show st22-539stats [<circuit name>]Displays statistics for ST2 circuits. You can limit the display to a specific circuit. The table includes the

Using Technician Interface Scripts2-540streamsSample Display – streamsT2 Streams------------- Desired Packet

show sta2-541show staThe show sta <option> commands display configuration, statistical, and status information about statistical thresholds and a

Using Technician Interface Scripts2-542configuration [<object ID>]Displays configuration information for all objects or for a specific object. The

show sta2-543stats [<object ID>]Displays statistical information for all objects that are keeping statistics or for a specific object. The table

Using Technician Interface Scripts2-544show stateThe show state command provides an overview of the router. The information displayed depends on your

show state2-545Sample Display – show state allMore Mode: OFF Lines per screen: 24----------------------------------------------------------------CSMA

Using Technician Interface Scripts2-546show swsThe show sws <option> commands display configuration and status information about Switch Services

show sws2-547backup_dialing circuitsDisplays primary circuits that are configured for dial backup. The display includes the following information:Sampl

viConfiguring Menus ...1-18Adding a Command ...

Using Technician Interface Scripts2-8Sample Display – show appn cos nodeAPPN COS Nodes-------------- Resist Resist Congest Congest C

Using Technician Interface Scripts2-548backup_dialing pools [<pool ID> [<circuit name>]]Displays detailed line information for each line i

show sws2-549ISDN Line Information:Hold Down Time Number of seconds the router waits before bringing up the line. This delay prevents the line from go

Using Technician Interface Scripts2-550Sample Display – show sws backup_dialing pools 1Switched Services Dial Backup Pool Information-----------------

show sws2-551backup_dialing schedulesDisplays the scheduled availability of the backup circuits in a backup pool. The display includes the following i

Using Technician Interface Scripts2-552Sample Display – show sws bandwidth circuitSwitched Services Bandwidth Circuit Information---------------------

show sws2-553bandwidth pool [<pool ID> [<circuit name>]]Displays detailed line information for each line in each pool. You can display inf

Using Technician Interface Scripts2-554ISDN Line InformationActive Circuit Name of the circuit using this line.Hold Down Time Number of seconds the ro

show sws2-555Sample Display – show sws bandwidth pool 1Switched Services Bandwidth Pool Information-------------------------------------------- PRIMA

Using Technician Interface Scripts2-556caller resolution tableDisplays the entries in the caller resolution table. The router uses the caller resoluti

show sws2-557ondemand_dialing circuitsDisplays all circuits configured for dial-on-demand. The display includes the following information:Sample Displa

show appn2-9Sample Display – show appn cos priorityAPPN COS Priorities------------------- COS Priority -------- -------- #BATCH Low #INTER

Using Technician Interface Scripts2-558Circuit Information:Synchronous Line Information:Circuit Circuit name of the demand circuit.Connection Mode Ope

show sws2-559ISDN Line InformationActive Circuit Name of the circuit using this line.Hold Down Time Number of seconds the router waits before bringing

Using Technician Interface Scripts2-560Sample Display – show sws ondemand_dialing pools 1Switched Services Dial OnDemand Pool Information-------------

show sws2-561ondemand_dialing schedulesDisplays the scheduled availability of each demand circuit in a demand pool.Sample Display – show sws ondemand_

Using Technician Interface Scripts2-562outbound filters {ip | data_link}For the ip and data_link options, the display includes the following informatio

show sws2-563Sample Display – show sws outbound_filters data_linkSwitched Services Data Link Outbound Filters Information------------------------------

Using Technician Interface Scripts2-564show syncThe show sync <option> commands display configuration, status, and statistical information about

show sync2-565State State of the line driver, as follows:• Disabled – User has manually disabled the driver.• Down – Driver is not operational.• DSR W

Using Technician Interface Scripts2-566Sample Display – show sync alertsSYNC Modules on Alert:----------------------

show sync2-567Sample Display – show sync baseSYNC Modules:------------- Line WAN Loc Rem Med

Using Technician Interface Scripts2-10For more information about COS types and weight, see the cos node command.Security Min Minimum security, with se

Using Technician Interface Scripts2-568enabledDisplays SYNC circuits that a user has manually enabled. For definitions of the columns in the table, see

show sync2-569Sample Display – show sync receiveSYNC Module Receive Errors:--------------------------- Bad Runt Frame

Using Technician Interface Scripts2-570Sample Display – show sync sampleSYNC Sampled Data over 10 seconds----------------------------------

show sync2-571Sample Display – show sync statsSYNC Module I/O Statistics:--------------------------- Receive Receive Transmit

Using Technician Interface Scripts2-572Sample Display – show sync systemSYNC Module System Errors:-------------------------- Receive

show sync2-573Sample Display – show sync transmit errorsSYNC Module Transmit Errors:---------------------------- UnderflowSlot Conn C

Using Technician Interface Scripts2-574show systemThe show system <option> commands display information about the system state, which pertains t

show system2-575driversDisplays link modules and drivers installed on all active slots in the system. If the configuration displayed differs from that

Using Technician Interface Scripts2-576informationDisplays general system information.Sample Display – show system informationSystem Information: ----

show system2-577protocolsDisplays which protocols are installed on all active slots in the system. If the configuration displayed differs from that exp

show appn2-11Sample Display – show appn cos tgAPPN COS TGs------------ Eff-Cap Connect ByteCst Securty Delay User-1 User-2 User-3

Using Technician Interface Scripts2-578versionDisplays the current version and modification date for the system.bat script.Sample Display – show system

show t12-579show t1The show t1 <option> commands display configuration, status, and statistical information about T1 lines. For detailed informat

Using Technician Interface Scripts2-580Frame Type Framing format. The following two framing formats differ in the number of frames per superframe and

show t12-581Sample Display – show t1 alertsT1 Modules on Alert:-------------------- Frame Line B8ZS Clock

Using Technician Interface Scripts2-582Sample Display – show t1 base circuit t1-21T1 Modules:----------- Frame Line B8ZS Clock

show t12-583enabledDisplays T1 circuits that a user has manually enabled. For definitions of the columns in the table, see the alerts command.Sample Di

Using Technician Interface Scripts2-584Sample Display – show t1 frame errorsT1 Module Frame Errors:----------------------- Frame Bit

show t12-585Sample Display – show t1 lineT1 Module Line Errors:---------------------- Yellow Red

Using Technician Interface Scripts2-586Sample Display – show t1 line errors circuit t1-21T1 Module Line Errors:----------------------

show tcp2-587show tcp The show tcp <option> commands display information about the Transmission Control Protocol (TCP). For detailed informatio

Using Technician Interface Scripts2-12Sample Display – show appn directory entryAPPN Directory Entries---------------------- LU NN S

Using Technician Interface Scripts2-588configurationDisplays the TCP configuration parameters. The table includes the following information:Sample Displ

show tcp2-589Except for Establish, Closed and Listen, all states are associated with establishing and closing a connection and are thus transitory.Sam

Using Technician Interface Scripts2-590statsDisplays statistical information for TCP. The table includes the following information:Sample Display – sh

show telnet2-591show telnetThe show telnet <option> commands display information about Telnet services. The show telnet command supports the fol

Using Technician Interface Scripts2-592configurationDisplays user configurable parameters for Telnet, as follows:Screen Size Default screen size in numb

show telnet2-593Sample Display – show telnet configuration TELNET Configuration Information -------------------------------- Screen Size: 24

Using Technician Interface Scripts2-594statsDisplays statistical information that the Telnet daemon records. The information includes the following:Sa

show tftp2-595show tftpThe show tftp <option> commands display information about the Trivial File Transfer Protocol (TFTP) status. For informati

Using Technician Interface Scripts2-596Sample Display – show tftp baseTFTP Base Information--------------------- Default Retransmi

show token2-597show token The show token <option> commands display configuration, status, and statistical information about Token Ring lines. For

show appn2-13Sample Display – show appn stats directoryAPPN Directory Statistics----------------------- Maximum Cached Entries: 100 Current

Using Technician Interface Scripts2-598Sample Display – show token alertsTOKEN RING Modules on Alert:----------------------------

show token2-599base [circuit <circuit name>]Displays the base information for all Token Ring circuits or a specific Token Ring circuit. For defini

Using Technician Interface Scripts2-600disabledDisplays Token Ring circuits that a user has manually disabled. For definitions of the columns in the ta

show token2-601receive errors [circuit <circuit name>]Displays receive errors for all circuits or for a specific circuit. The table includes the

Using Technician Interface Scripts2-602sample [<period in seconds>] [circuit <circuit name>]Displays data sampled from Token Ring over a p

show token2-603stats [circuit <circuit name>]Displays Token Ring input/output statistical information for all Token Ring circuits or for a speci

Using Technician Interface Scripts2-604stats line [circuit <circuit name>]Displays Token Ring line statistical information for all Token Ring ci

show token2-605Sample Display – show token stats line circuit o41TOKEN RING Line Statistics:--------------------------- ARI/FCI

Using Technician Interface Scripts2-606Sample Display – show token stats ringTOKEN RING Ring Statistics:--------------------------- B

show token2-607Sample Display – show token system errorsTOKEN RING System Errors:------------------------- Adapter DMA Bus DMA

Using Technician Interface Scripts2-14Sample Display – show appn dlcAPPN DLCs--------- DLC Negotiated

Using Technician Interface Scripts2-608Sample Display – show token transmitTOKEN RING Transmit Errors:---------------------------

show vines2-609show vinesThe show vines <option> commands display information about Virtual Networking System (VINES) services on a Bay Networks

Using Technician Interface Scripts2-610alertsDisplays the VINES interfaces that are enabled but not currently up. Use this command to identify interfa

show vines2-611Sample Display – show vines alertsVINES Circuit Table------------------- End Remote Split Circuit

Using Technician Interface Scripts2-612Sample Display – show vines baseVINES Base Record Information----------------------------- Protocol State Bc

show vines2-613configuration [circuit [<circuit name>] ]Displays configurable parameters from the VINES protocol base record. For column definition

Using Technician Interface Scripts2-614enabledDisplays VINES interfaces that have been configured as enabled and whose state is active. For column defin

show vines2-615The table includes the following fields:Sample Display – show vines neighborsVINES Neighbors--------------- Network Subnet

Using Technician Interface Scripts2-616The table includes the following fields:Sample Display – show vines routesVINES Routes------------Network Id Met

show vines2-617Sample Display – show vines statsVINES Circuit Statistics-------------------------- In In Out Out Forwar

show appn2-15Sample Display – show appn dlur luAPPN DLUR LUs------------- NAU LU PU

Using Technician Interface Scripts2-618stats icp [<circuit name>]Displays VINES Internet Control Protocol (ICP) statistics for the whole router.

show vines2-619Sample Display – show vines traffic filtersVINES Traffic Filters Table--------------------------- Rx R

Using Technician Interface Scripts2-620show wcpThe show wcp <option> commands display information about Bay Networks data compression (WCP) serv

show wcp2-621Sample Display – show wcp circuitsWCP Circuit Entries------------------- Circuit Circuit Compression History Name Number En

Using Technician Interface Scripts2-622Sample Display – show wcp linesWCP Line Entries---------------- Line Co

show wcp2-623Sample Display – show wcp vcsWCP Virtual Circuit Entries--------------------------- Line Vc Compression Decomp

Using Technician Interface Scripts2-624Sample Display – show wcp statsWCP Performance And Data Statistics----------------------------------- Line

show wcp2-625Sample Display – show wcp stats errorsWCP Error Statistics-------------------- Line Vc Compression Decompression

Using Technician Interface Scripts2-626versionDisplays the current version number and date of the wcp.bat script.Sample Display – show wcp versionWCP.

show x252-627show x25 The show x25 <option> commands display information about X.25 services. For complete information about the Bay Networks im

Using Technician Interface Scripts2-16dlus [<DLUS name>]Displays the status of all the DLUSs or a specific DLUS. Sample Display – show appn dlusA

Using Technician Interface Scripts2-628Sample Display – show x25 alertsX.25 Packet Level Alert Status------------------------------ Restarts Rese

show x252-629configuration [<slot.connector>]Displays the basic configuration information for all X.25 lines or displays that only the slot and co

Using Technician Interface Scripts2-630Sample Display – show x25 connectionsX.25 Virtual Circuit Connections Total VC Failed VC Normal VC

show x252-631Sample Display – show x25 lineX.25 Packet Line Configuration Network Def Def Standard Local X.121

Using Technician Interface Scripts2-632Sample Display – show x25 servicesX.25 Network Services Configuration-----------------------------------

show x252-633Sample Display – show x25 statsX.25 Packet Line Statistics--------------------------- Max LCN's RX TX Restarts R

Using Technician Interface Scripts2-634Sample Display – show x25 vcX.25 Virtual Circuit Statistics------------------------------- VC

show xb2-635show xbThe show xb <option> commands display information about the Translation Bridge (XB). For detailed information on the Bay Netw

Using Technician Interface Scripts2-636Sample Display – show xb alertsSource Routing Circuits----------------------- Circuit Mode State------- -

show xb2-637configurationDisplays how a Translation Bridge has been configured globally. The table includes the following information:Sample Display – s

show appn2-17Sample Display – show appn endpoint addressAPPN Endpoint Session Addressing Info------------------------------------- Partner LU

Using Technician Interface Scripts2-638Sample Display – show xb disabledSource Routing Circuits----------------------- Circuit Mode State-------

show xb2-639Sample Display – show xb enabledSource Routing Circuits----------------------- Circuit Mode State------- ------- -----O31 Enab

Using Technician Interface Scripts2-640Sample Display – show xb rifsTranslation Bridge (XB) Learned RIFs------------------------------------ MAC Ad

show xb2-641Sample Display – show xb sr circuit o31Source Routing Circuits----------------------- Circuit Mode State------- ------- -----O31

Using Technician Interface Scripts2-642stationsDisplays how the Translation Bridge will convert packets destined for Ethernet stations. MAC Address w

show xb2-643Sample Display – show xb tbTransparent Bridge Circuits--------------------------- Circuit Mode State -------- -------- -------- 2021

Using Technician Interface Scripts2-644versionDisplays the current version and modification date of the xb.bat script.Sample Display – show xb versionX

show xns2-645show xns The show xns <option> commands display information about the Xerox Network Systems (XNS) services on Bay Networks routers.

Using Technician Interface Scripts2-646alertsDisplays the XNS interfaces that are enabled but not currently up. Use this command to identify interface

show xns2-647Sample Display – show xns adjacent hostsXNS Static Adjacent Hosts--------------------------Host Network

viishow fddi ...2-252show fr ...

Using Technician Interface Scripts2-18Sample Display – show appn endpoint routeAPPN Endpoint Session Routing Info----------------------------------

Using Technician Interface Scripts2-648circuit [<circuit name>]Displays parameters for all XNS circuits or for a specific circuit. For column defi

show xns2-649disabledDisplays XNS circuits that are disabled and down. In this case, State is always Down. For column definitions in the display, see t

Using Technician Interface Scripts2-650rip [alerts | disabled enabled | <XNS network>] Displays the status of XNS Routing Information Protocol (

show xns2-651routes [<network address> | find <address pattern>]Displays information from the XNS routing table. The table acquires routes

Using Technician Interface Scripts2-652static routesDisplays all configured XNS static routes. The table includes the following information:Sample Disp

show xns2-653Sample Display – show xns statsXNS Circuit Statistic(s) Table------------------------------ In Out

Using Technician Interface Scripts2-654Sample Display – show xns stats errorsXNS Circuit Error Statistics Table----------------------------------

show xns2-655traffic filters [<circuit name>] Displays traffic filter information for all circuits or for a specific circuit. The table includes the

3-1Chapter 3Using enable/disable CommandsYou can enable and disable network protocols, services, and interfaces from the Technician Interface command

show appn2-19Sample Display – show appn stats endpointAPPN Endpoint Session Statistics--------------------------------

Using Technician Interface Scripts3-2enable/disable appnUse the enable appn <option> commands to enable APPN services on a Wellfleet router, and

enable/disable appn3-3directory <LU name>Enables or disables a specific Logical Unit directory.Sample Display – enable appn directoryEnter Fully-

Using Technician Interface Scripts3-4port <port name>Enables or disables a specific APPN port.Sample Display – enable appn portEnter Port Name: P

enable/disable at3-5enable/disable atUse the enable at <option> commands to enable AppleTalk services on a Bay Networks router, and the disable

Using Technician Interface Scripts3-6enable/disable atmUse the enable atm <option> commands to enable ATM Adaptation Layer Controller (ALC) link

enable/disable atm3-7line connector <slot.connector>Enables or disables a specific ATM connector.Sample Display – enable atm line connector 5.1AT

Using Technician Interface Scripts3-8enable/disable atmdxiUse the enable atmdxi commands to enable Asynchronous Transfer Mode Data Exchange Interface

enable/disable aurp3-9enable/disable aurpUse the enable aurp <option> commands to enable AppleTalk Update-based Routing Protocol (AURP) services

Using Technician Interface Scripts3-10enable/disable autonegUse the enable autoneg <option> commands to enable automatic line speed negotiation

enable/disable bootp3-11enable/disable bootpUse the enable bootp <option> command to enable BOOTP (bootstrap protocol) services on a Bay Network

Using Technician Interface Scripts2-20Sample Display – show appn isr addressAPPN ISR Session Addressing Info-------------------------------- FQ CP

Using Technician Interface Scripts3-12enable/disable bridgeUse the enable bridge <option> commands to enable Bridging services on a Bay Networks

enable/disable circuits3-13enable/disable circuitsUse the enable circuits <option> commands to enable a driver circuit on a Bay Networks router,

Using Technician Interface Scripts3-14enable/disable csmacdUse the enable csmacd <option> commands to enable Carrier Sense Multiple Access with

enable/disable dcmmw3-15enable/disable dcmmwOn a Bay Networks 8-Port ANH with an installed N11 Data Collection Module (DCM) option, use the enable dcm

Using Technician Interface Scripts3-16enable/disable decnetUse the enable decnet <option> commands to enable DECnet services on a Bay Networks r

enable/disable dls3-17enable/disable dlsUse the enable dls <option> commands to enable Data Link Switching (DLSw) services on a Bay Networks rou

Using Technician Interface Scripts3-18enable/disable ds1e1Use the enable ds1e1 <option> commands to enable MCT1 and MCE1 services on a Bay Netwo

enable/disable dvmrp3-19enable/disable dvmrpUse the enable dvmrp <option> commands to enable DVRMP services on a Bay Networks router, and the di

Using Technician Interface Scripts3-20enable/disable e1Use the enable e1 <option> commands to enable E1 services on a Bay Networks router, and t

enable/disable fddi3-21enable/disable fddiUse the enable fddi <option> commands to enable Fiber Distributed Data Interface (FDDI) services on a

show appn2-21Sample Display – show appn isr parametersAPPN ISR Parameters------------------- ISR State: Enabled Maximum R

Using Technician Interface Scripts3-22enable/disable frUse the enable fr <option> commands to enable Frame Relay services on a Bay Networks rout

enable/disable ftp3-23enable/disable ftpUse the enable ftp <option> commands to enable File Transfer Protocol (FTP) services on a Bay Networks r

Using Technician Interface Scripts3-24enable/disable hssiUse the enable hssi <option> commands to enable High-Speed Serial Interface (HSSI) serv

enable/disable igmp3-25enable/disable igmpUse the enable igmp <option> commands to enable IGMP services on a Bay Networks router, and the disabl

Using Technician Interface Scripts3-26enable/disable ipUse the enable ip <option> commands to enable Internet Protocol (IP) services on a Bay Ne

enable/disable ipx3-27enable/disable ipxUse the enable ipx <option> commands to enable Novell’s Internet Packet Exchange (IPX) services on a Bay

Using Technician Interface Scripts3-28enable/disable iredundUse the enable iredund <option> commands to enable interface redundancy on a Bay Net

enable/disable isdn3-29enable/disable isdnUse the enable isdn <option> commands to enable Integrated Services Digital Network (ISDN) services on

Using Technician Interface Scripts3-30filter <slot>Enables or disables a specific ISDN filter.Sample Display – enable isdn filter <slot>Incomi

enable/disable isdn bri3-31enable/disable isdn briUse the enable isdn bri <option> commands to enable Integrated Services Digital Network Basic

Using Technician Interface Scripts2-22isr statistics [<FQCP name>]Displays session statistics for all ISR sessions or for ISR sessions from a sp

Using Technician Interface Scripts3-32enable/disable lapbUse the enable lapb <option> commands to enable Link Access Procedure-Balanced (LAPB) s

enable/disable lnm3-33enable/disable lnmUse the enable lnm <option> commands to enable LNM Servers services on a Bay Networks router, and the di

Using Technician Interface Scripts3-34enable/disable nbipUse the enable nbip <option> commands to enable NetBIOS services on a Bay Networks rout

enable/disable nml3-35enable/disable nmlUse the enable nml <option> commands to enable Native Mode LAN (NML) services on a Bay Networks router,

Using Technician Interface Scripts3-36enable/disable osiUse the enable osi <option> commands to enable Open Systems Interconnection (OSI) servic

enable/disable ospf3-37enable/disable ospfUse the enable ospf <option> commands to enable Open Shortest Path First (OSPF) services on a Bay Netw

Using Technician Interface Scripts3-38enable/disable packetUse the enable packet <option> commands to enable the Packet Capture utility on a Bay

enable/disable ppp3-39enable/disable pppUse the enable ppp <option> command to enable Point-to-Point Protocol (PPP) services on a Bay Networks r

Using Technician Interface Scripts3-40enable/disable rarpUse the enable rarp <option> command to enable Reverse Address Resolution Protocol (RAR

enable/disable rptr3-41enable/disable rptrUse the enable rptr <option> commands to enable Access Node (AN) Repeater services, and the disable rp

show appn2-23Sample Display – show appn ls anrAPPN Link Station ANR Info --------------------------- ANR

Using Technician Interface Scripts3-42enable/disable rredundUse the enable rredund <option> commands to enable router redundancy (RREDUND) servi

enable/disable sdlc3-43enable/disable sdlcUse the enable sdlc <option> commands to enable Synchronous Data Link Control (SDLC) services on a Bay

Using Technician Interface Scripts3-44enable/disable spanUse the enable span <option> commands to enable Spanning Tree Bridge services on a Bay

enable/disable sr3-45enable/disable srUse the enable sr <option> commands to enable Source Routing services on a Bay Networks router, and the di

Using Technician Interface Scripts3-46enable/disable srspanUse the enable srspan <option> commands to enable Source Route Spanning Tree Bridging

enable/disable sta3-47enable/disable staUse the enable sta <option> commands to enable Statistical Thresholds and Alarms (STA) services on a Bay

Using Technician Interface Scripts3-48enable/disable swsUse the enable sws <option> commands to enable Switched Services on a Bay Networks route

enable/disable sync3-49enable/disable syncUse the enable sync <option> commands to enable synchronous services on a Bay Networks router, and the

Using Technician Interface Scripts3-50enable/disable t1Use the enable t1 <option> commands to enable T1 services on a Bay Networks router, and t

enable/disable tcp3-51enable/disable tcpUse the enable tcp <option> commands to enable Transmission Control Protocol (TCP) services on a Bay Net

Using Technician Interface Scripts2-24Sample Display – show appn ls definitionAPPN Link Station Definition----------------------------

Using Technician Interface Scripts3-52enable/disable telnetUse the enable telnet <option> commands to enable Telnet services on a Bay Networks r

enable/disable tftp3-53enable/disable tftpUse the enable tftp <option> commands to enable Trivial File Transfer Protocol (TFTP) services on a Ba

Using Technician Interface Scripts3-54enable/disable tokenUse the enable token <option> commands to enable Token Ring services on a Bay Networks

enable/disable vines3-55enable/disable vinesUse the enable vines <option> commands to enable Virtual Networking System (VINES) services on a Bay

Using Technician Interface Scripts3-56enable/disable wcpUse the enable wcp <option> commands to enable Wellfleet Compression Protocol (WCP) servi

enable/disable x253-57enable/disable x25Use the enable x25 <option> commands to enable X.25 services on a Bay Networks router, and the disable x

Using Technician Interface Scripts3-58enable/disable xbUse the enable xb <option> commands to enable Translation Bridge services on a Bay Networ

enable/disable xns3-59enable/disable xnsUse the enable xns <option> commands to enable Xerox Network Systems (XNS) services on a Bay Networks ro

A-1Appendix APacket ConfigurationThe config packet command enables you to configure the Packet Capture utility using the Technician Interface. For inform

show appn2-25Sample Display – show appn ls hprAPPN Link Station HPR info ------------------------------ HPR Link Lev

Using Technician Interface ScriptsA-2• Capture buffer size• Packet save size• Capture direction options — receive, transmit, or both• Receive trigger

Packet ConfigurationA-3Sample Display – config packet lineconfig packet linePerforming mount check...Packet Capture Line Configuration-----------------

Using Technician Interface ScriptsA-4Capture Direction Options-------------------------1: Receive2: Transmit3: Receive and TransmitCurrent value for C

Packet ConfigurationA-5Receive Filter One Reference Options------------------------------------1: Mac2: Data Link3: MulticastCurrent value for Receive

Using Technician Interface ScriptsA-6config packet load [<slot>]config packet load [<slot_number>] loads the Packet Capture utility on the s

Index-1Symbols* character, 2-1? character, 2-1Aaarpat, 2-44Adaption Layer Controller, 1-8, 2-84Address Resolution ProtocolIP, 2-301addressessmds, 2-50

Index-2ARP, IP, 2-301ase informationospf, 2-415Asynchronous Transfer Mode, 2-58 to 2-78enabling/disabling, 3-8AT subcommands, 2-43 to 2-57audience for

Index-3Bootstrap PROMrevision date, 2-283Bootstrap Protocol (BOOTP), 2-130 to 2-134Border Gateway Protocol (BGP), 2-111 to 2-119Bridge NCPPPP, 2-440br

Index-4vines, 2-613x25, 2-629xb, 2-637xns, 2-648configuration filehardware, 2-281ConnectionLess Network Protocolstatistics, 2-412connectionsaurp, 2-98dl

Index-5xb, 2-637xns, 2-649disabled linespacket, 2-428disabled serial portsconsole, 2-164Displays, 2-370DLSw protocolpriority queues, 2-468 to 2-471DLS

Using Technician Interface Scripts2-26Sample Display – show appn ls statusAPPN Link Station Status------------------------

Index-6decnet, 2-190dls, 2-202ds1e1, 2-215dvmrp, 2-234e1, 2-245fddi, 2-255fr, 2-270hssi, 2-289igmp, 2-296ip, 2-304ipx, 2-330isdn bri, 2-371lnm, 2-396o

Index-7hardware information, 2-279 to 2-285hardware subcommands, 2-279 to 2-285High-Speed Serial Interface, 2-286HSSI, 2-286 to 2-294enabling/disablin

Index-8local router namePPP, 2-449lqrconfigurationppp, 2-452statisticsppp, 2-453lsdbospf, 2-418Mmacdls, 2-204fddi, 2-257MAC addressDLS, 2-204Management

Index-9OSPF subcommands, 2-414 to 2-421OUIATM protocol, 2-77Ppacket captureenabling/disabling, 3-38Packet Capture, configuring, A-1Packet Capture, enab

Index-10routesat, 2-51bgp, 2-114ip, 2-308ipx, 2-337level 1osi, 2-410level 2osi, 2-410staticIP, 2-311IPX, 2-349vines, 2-615xns, 2-651Routing Informatio

Index-11hssi, 2-286 to 2-294igmp, 2-295 to 2-298ipx, 2-323 to 2-355irredund, 2-356isdn, 2-359 to 2-367isdn bri, 2-368 to 2-374lapb, 2-384 to 2-388list

Index-12stationsxb, 2-642statistical thresholds, 2-541statistics, 2-146all driver circuits, 2-156at, 2-53atm, 2-64 to 2-65atm line, 2-91, 2-93 to 2-95

Index-13TT1, 2-579 to 2-586enabling/disabling, 3-50T1 subcommands, 2-579 to 2-586tasksshow system command, 2-577TBXB, 2-642TCP, 2-587 to 2-590TCP subc

Index-14WWCP, 2-620 to 2-626, 3-56weightsbgp, 2-119wildcard searching, 2-1XX.25 services, 2-627 to 2-634enabling/disabling, 3-57X25 subcommands, 2-627

show appn2-27mode [<mode name>]Displays mode-to-COS mappings for all modes or for a specific mode. For information on the columns, see the cos no

viiishow state ...2-544show sws ...

Using Technician Interface Scripts2-28Sample Display – show appn port definitionAPPN Port Definitions--------------------- Re

show appn2-29Sample Display – show appn port hprAPPN Port Defined HPR info ----------------------------- Implicit Implicit Implicit

Using Technician Interface Scripts2-30Sample Display – show appn port statusAPPN Port Status---------------- Port Number State Link Rol

show appn2-31Sample Display – show appn rtp connectionAPPN RTP Connections-------------------- RTP 1st Hop

Using Technician Interface Scripts2-32rtp statisticsDisplays statistics for all RTP connections or a specific RTP connection.Sample Display – show appn

show appn2-33topology node [<CP name>]Displays node information on the topology database for all control points or for a specific control point.N

Using Technician Interface Scripts2-34Sample Display – show appn topology nodeAPPN Topology Nodes------------------- Node Type FRSN RS

show appn2-35Received TDUs Number of TDUs received from all adjacent network nodes since last initialization.Sent TDUs Number of TDUs built by this no

Using Technician Interface Scripts2-36TG Record Statistics:Received Low RSNs Number of topology transmission group updates received by this node with

show appn2-37Sample Display – show appn topology statisticsAPPN Topology Statistics-----------------------Node Record Statistics ---------------------

ixenable/disable hssi ...3-24enable/disable igmp

Using Technician Interface Scripts2-38topology tg definition [<owner name>]Displays transmission group information for all transmission group own

show appn2-39Sample Display – show appn tg definitionAPPN Topology TG Definition--------------------------- TG Eff

Using Technician Interface Scripts2-40Sample Display – show appn tg statusAPPN Topology TG Status-----------------------

show appn2-41Sample Display – show appn tunnelAPPN Tunnels------------ Frames Frames Frames CCT Partner Node

Using Technician Interface Scripts2-42Sample Display – show appn vrnAPPN Virtual Routing Nodes-------------------------- VRN State

show at2-43show atThe show at <option> commands display information about the AppleTalk protocol and services. For detailed information on the B

Using Technician Interface Scripts2-44aarp [<net>.<node> | find <net>]Displays all entries in the AppleTalk Address Resolution Prot

show at2-45alertsDisplays all AppleTalk circuits that are enabled but not up. Mode is always Enabled but the state will be down. Use this display to i

Using Technician Interface Scripts2-46baseDisplays the base record information for AppleTalk. The base record controls AppleTalk for the entire system

show at2-47Sample Display – show at circuit AppleTalk Circuit Information ------------------------------- Circuit State Network Address